| Installation |
| |
STANDARD | Instructions |
| |
COLLECTION |
| 6718 |
|
18" TOWEL BAR |
| 6724 |
|
24" TOWEL BAR |
|
|
|
Thank you for selecting |
|
| |
of fine quality for over 100 years. |
|
|
|
To ensure that your installation proceeds |
|
| |
read these instructions carefully before you begin. | Certified to comply with ANSI A112.18.1 | M 9 6 8 2 1 7 B | |
|
| U.S. Patent No. D403,750 |
Regular Screwdriver
10' | Drill |
| |
Tape Measure | Phillips Screwdriver |
|
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.
The 18" TOWEL BAR (1) and 24' TOWEL BAR (2) work best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied.
If the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) is to be installed on a tile or plaster wall the TILE ANCHORS (4) or DRYWALL ANCHORS (6) and SCREWS (3) should be used.
Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) mark a centerline 24" horizontally from the first location. For the 18" TOWEL BAR (1) mark a centerline 18" from the first location. Using the MOUNTING PLATE (5) as a template mark the two mounting holes. Repeat for the other MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or cross brace, drill small pilot holes for SCREWS (4).
For installations on drywall, use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS (6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).
For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill two 1/4" diameter holes a minimum of
Install the WALL ESCUTCHEON (7) on the MOUNTING PLATE (5). Place the 18" TOWEL BAR (1) and 24' TOWEL BAR (2) into the SIDE SUPPORT BRACKET (10, 10a). Align slot in towel bar with notch in recess of support post (10, 10a) (see Figure A). Place the18" TOWEL BAR (1) and 24' TOWEL BAR (2) on the ESCUTCHEON (7) and MOUNTING BRACKET (5). Secure with MOUNTING SCREW (8). Tighten fully.
Push INDEX BUTTONS (9) into SIDE SUPPORT BRACKET (10, 10a). See illustration.
4 | USE MOUNTING PLATE | 3 7 |
| AS TEMPLATE |
|
3 | 5 | 6 |
|
| 8 |
|
|
|
|
| |
|
|
| CENTER | 4 |
|
|
|
| LINE |
|
|
|
|
|
|
| 9 |
|
|
| 48 TO 72 |
|
|
|
|
| INCHES FROM | 5 | 10 10a |
|
|
| FLOOR | ||
|
| 6 | 4 |
| FINISHED |
|
|
|
|
| WALL |
24"
1 2
|
|
| SLOT IN TOWEL BAR |
CENTER LINE |
|
|
|
| 48" TO 60" | Figure A | NOTCH IN RECESS OF SUPPORT POST |
18" | (OPTIONAL) | ||
|
|
|