American Standard 7160.804 dimensions Double Bowl Dual Level Sink, Acid-resistingenameled steel

DOUBLE BOWL DUAL LEVEL SINK

ENAMELED STEEL

DOUBLE BOWL DUAL LEVEL KITCHEN SINK

•Acid-resisting enameled steel

•Dual level, double bowl design

•Self-rimming installation

•Shown with 4205.660 Silhouette faucet (not included)

•Silicone sealant supplied

•Available in 3, 4, or 5 faucet hole configuration

❏7160.803 3 hole

❏7160.804 4 hole

❏7160.805 5 hole

Nominal Dimensions: 838 x 559 x 184mm (33" x 22" x 7-1/4")

Bowl sizes:

Large Bowl: 527mm (20-3/4") wide, 413mm (16-1/4") front to back 178mm (7") deep Small Bowl: 187mm (7-3/8") wide, 413mm (16-1/4") front to back 146mm (5-3/4") deep

Compliance Certifications -

Meets or Exceeds the Following Specifications:

•ASME A112.19.4M for Enameled Steel Plumbing Fixtures

To Be Specified

❏Color: (specify White Heat or Bone)

❏Faucet*: (specify finish)

❏Basket Strainer: 4331.013 (Chrome only)

❏Soap Dispenser*: 4503.115 (specify color)

❏Trap:

*See faucet section for additional models available

			FINISHED WALL		102mm	102mm
					(4)
			OR SPLASHBACK			(4)	102mm
							(4)	38mm (1-1/2)
				C/L				DIA. HOLES TYP.
51mm (2)		102mm(4)						54mm
OPTIONAL								(2-1/8)
206mm
(8-1/8)
311mm								7160.804
(12-1/4 )
								4 HOLE
7160.805
5 HOLE
89mm								559mm
(3-1/2)
								(22)
DIA.
38mm (1-1/2)			133mm					*CUTOUT NOTE
RAD. TYP.			(5-1/4)
		432mm			267mm
		(17)
					(10-1/2)
				838mm
13mm				(33)	203mm
	SEALING						COUNTERTOP
(1/2)
					(8)
	COMPOUND						(BY OTHERS)
								X
171mm								140mm
								(5-1/2)
(6-3/4)								▼Y
							146mm
146mm							(5-3/4)
(5-3/4)				▼ 3/8 O.D. COUNTERTOP
	1-1/2 O.D. TAILPIECE			BENDABLE
914mm (36)				TUBING
	COUPLING NUTS
SUGGESTED					21mm
	ON FITTING
					(13/16)
FINISHED FLOOR
					MAX.			LUG AND
								SCREW
					CLAMPING DETAIL			ASSEMBLY
FAUCET				7160.803	7160.804		X	Y▼
CERAMIX				2021.700	2021.741		—	327mm(12-7/8)
RELIANT				4205.241	4205.217		—	254mm(10)
HERITAGE	TOP MOUNT			6270.000	6279.000		44mm(1-3/4)	—
AMARILIS	BOTTOM MOUNT		7270.SER.		7271.SER.		95mm(3-3/4)	—

NOTES:

COUNTERTOP CUTOUT 800 X 521MM WITH 19MM RADIUS (31-1/2 X 20-1/2 WITH 3/4” RAD.) AT CORNERS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.6

These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

KSS-014

4/98 © 1998 American Standard Inc.