American Standard 7391.224, 7391.229 installation instructions Bidet Faucet Installation

		Installation
Williamsburg	T M	Instructions
		7391.229
BIDET FITTING		7391.224

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ASME A112.18.1M U.S. Patent No. 5,819,789

M 9 6 8 0 3 2 A

	Roughing-in Dimensions						8 TO 12
	TRANSFER VALVE (FOR FLUSHING
		RIM OR SPRAY)
	BIDET OUTLINE					(C)	(H)
	IS SYMBOLIC	7/8 DIA.
CARE INSTRUCTIONS:					1-3/16 DIA.
	DOUCHE SPRAY	ADJ. 1-1/4	2-1/8		1-1/4 MAX.
DO: SIMPLY RINSE THE PRODUCT CLEAN		TO 2-1/4	DIA.
WITH CLEAR WATER. DRY WITH A SOFT		1-3/8
COTTON FLANNEL CLOTH.	3-7/8
		DIA.
DO NOT: CLEAN THE PRODUCT WITH SOAPS,		5-1/2
ACID, POLISH, ABRASIVES, HARSH CLEANERS,				FINISHED	FINISHED
OR A CLOTH WITH A COARSE SURFACE.					FLOOR
				WALL
				1-1/4 O.D. TAILPIECE

DIVERTER AND VACUUM BREAKER ASSEMBLY

2-1/4 DIA.

4-1/4

FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

1 BIDET FAUCET INSTALLATION

CAUTION	Turn off hot and cold water
	supplies before beginning.

Place MOUNTING NUTS (1) onto the VALVE BODIES

(2) and insert VALVE BODIES (2) through outside

holes, from underside of the BIDET LEDGE. Drop the

2 DRAIN INSTALLATION	STOPPER
Assemble O-RING (1), WASHER (2), PIVOT ROD (3)	9
and NUT (4) to DRAIN BODY (5). Concave side
of cup WASHER (2) is toward ball.

RUBBER RING (3) over the VALVE BODIES (2) and

screw on the ESCUTCHEON (4) until it locks against

the internal stop.

Tighten the MOUNTING NUT (1) to secure the VALVE BODY (2).

Remove MOUNTING NUT (9) and UPPER GASKET (7) from TRANSFER VALVE (8) and insert into the center forward hole of BIDET.

Replace UPPER GASKET (7). Position the side threaded outlet rearward and secure MOUNTING NUT (9). Thread ESCUTCHEON (5) onto TRANSFER VALVE (8) until it seats against the BIDET LEDGE.

5

9

4

Thread LOCKNUT (6), WASHER (7) and GASKET (8) onto DRAIN BODY (5).

Apply a bead of PUTTY to underside of FLANGE (9).

Feed DRAIN BODY (5) up through BIDET and thread FLANGE (9) fully onto BODY (5).

Tighten LOCKNUT (6) firmly, keeping the PIVOT ROD (3) pointed towards the back of the BIDET.

Push DRAIN ESCUTCHEON (10) onto TAILPIECE (11).

	PUTTY
8	BIDET
	CLIP

7	4
	2
6	3
	1

5

11

10

3

BIDET

LEDGE

2

HOTCOLD

17

8

3	SPRAY INSTALLATION	7	2	8
			PUTTY	1
	Assemble SPRAY BODY (1) to BIDET. 6
			7
	Using putty, seal underside of SPRAY
	BODY FLANGE (2) and secure with	5
	NUT (3).			3
	Screw SPRAY HOSE (4) with SEAL			5
	WASHER (5) to SPRAY BODY (1).
	Connect other end of HOSE (4) with

SEAL WASHER (5) to side outlet	4
NIPPLE (6) of the TRANSFER VALVE (7).

Screw SPRAY CAP (8) onto SPRAY BODY (1).