4 LIFT ROD GUIDE INSTALLATION
5 TEE AND HOSE CONNECTION
3
Unscrew LIFT ROD NUT (1)from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated into ESCUTCHEON of LIFT ROD GUIDE (2).
Drop LIFT ROD GUIDE (2) into |
|
rear hole of bidet and from |
|
below secure with ROD GUIDE |
|
NUT (1). | 2 |
|
3
1
Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to bottom of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2)
Connect HOSE COUPLING | 6 | |
NUTS (6) to Hot and Cold |
|
|
valve bodies and securely |
|
|
tighten. |
|
|
|
|
|
1
2
4 
6
5
6 HANDLE INSTALLATION
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without spline is facing up. See figure "A".
Screw HANDLE BASE (3) on top of ESCUTCHEON (4) until it is snug against stop.
Push LEVER BALL (5) through HANDLE BASE (3) onto ADAPTER (1).
Find correct position of LEVER BALL (5) by adjusting male teeth on ADAPTER (1) to female teeth in LEVER BALL (5).
Secure LEVER BALL (5) with HANDLE SCREW (6).
Push INDEX CAP (7) in hole of LEVER BALL (5). | 7 |
| 6 |
| 5 |
| 3 |
| TOP |
Figure "A" | 1 |
| |
| 2 |
SPLINE END DOWN | 4 |
8 FINISH DRAIN INSTALLATION
7 WATER SUPPLY CONNECTIONS
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE
PURCHASED SEPARATELY.
Connect water supplies to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D.
Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.
1
2 | COUPLING NUT |
3
FERRULE
9 SERVICE
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90° and replace. Replace SPRING CLIP (1).
Replace ADAPTER, HANDLE, SCREW, and INSERT.
Position BIDET fixture and secure to floor.
2
3
1
Spray may accumulate dirt |
|
causing distorted and reduced | 90° |
water flow. Remove spray and | 2 |
Insert lift rod into lift rod guide.
Position EXTENSION ROD (1) onto
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends together while sliding.
Insert PIVOT ROD (7) into second
1
7
5
4
rinse clean. | 1 |
|
Replace Spray and operate handles several times from OFF to ON position. Do not force, handles turn only 90˚.
or third hole in EXTENSION ROD (1) and reassemble CLIP (4).
(EXTENSION ROD (1) may need to be bent.)
6
10 TEST INSTALLED FAUCET
With handles in OFF position, turn on water supplies and
Adjust STOPPER height by repositioning EXTENSION ROD (1) and tightening THUMBSCREW (3).
Using metal TAILPIECE (5), make connection to the TRAP (6).
check all connections for leaks.
Operate both handles to flush water lines thoroughly. Turn diverter to rim wash and bidet spray.
M 9 6 8 0 3 2 A
