| AFTER THE CUTOUT IS DRAWN... | 7 | Rotate each | |
1 |
|
| ||
|
|
| retaining clip | |
Drill a clearance hole | Perimeter |
| toward sink bowl. | |
| inside the cutout line | of sink |
|
|
|
|
|
| |
| as marked on the |
|
|
|
| countertop. |
| 8 | Apply a generous portion of sealant inside line |
|
| Cutout | ||
|
|
|
| traced on countertop. Carefully lower sink into |
2 Cut opening on cut line |
|
| cutout and press down firmly. Use guidelines | |
|
| for proper positioning. | ||
| 9 |
| ||
| inside the perimeter of sink. | Perimeter |
| |
| Note - Formica countertop | of sink | Rotate each clip to | |
| installation only is illustrated. |
| ||
| Contact your countertop |
|
| engage countertop. |
| distributor for the best method |
|
| NOTE - TIGHTEN |
| of cutting other materials such |
|
| THE TWO CENTER |
| as marble, hard synthetics, | Cutout |
| CLIPS ON EACH |
| etc. |
|
| LONG SIDE OF THE |
|
|
|
| |
3 |
|
|
| SINK FIRST ( SEE |
Mount the faucet and |
|
| FIGURE 3 FOR DETAILS). Complete the | |
|
| tightening process for the remaining clips, | ||
| drain assembly on the |
|
| to secure sink. Remove excess sealant from |
| sink or countertop |
|
| |
|
|
| countertop for a smooth even line of sealant | |
| following the |
|
| |
|
|
| around the edge of the sink. | |
| manufacturer's |
|
| |
| instructions. |
|
|
|
4 | Before applying the sealant, | 10 |
place the sink temporarily | Connect supply lines | |
| into the cutout. Check for | to faucet finger tight, |
| and carefully bend to | |
| alignment and clearance, | |
| engage with the | |
| then trace around the | |
| supply stops. Tighten | |
| outside edge of the sink as | |
| connections to faucet | |
| a guide for installation | |
| for secure seal. | |
| location and application | |
|
| |
| of sealant. |
|
5 Remove sink and |
|
|
| 11 Connect drain assembly |
|
|
Cutout |
|
| hand tight to check align- |
|
| |
apply a masking tape |
|
| ment. It may be necessary |
| B | |
outline 1/8" outside |
|
|
| to cut off part of the | A | |
|
|
| tailpiece (area "A") or part |
| ||
traced outline as a |
|
| Sink |
|
| |
Masking |
| of the horizontal leg of the |
|
| ||
guide for application |
|
|
| |||
tape outline | 1/8" | outline | trap (area "B"). |
|
| |
of silicone sealant. |
|
|
| |||
|
|
|
|
|
| |
6 |
|
|
| Secure joint for watertight |
|
|
|
|
| assembly. |
|
| |
|
|
|
|
|
| |
|
|
|
| Trap | Trap |
|
| LOCKING TAB |
| Single Bowl | Double Bowl |
| |
|
| 12 Note: The clips supplied with sink can be used for | ||||
| NOTCH |
|
| |||
|
|
|
| a countertop with a thickness of 1/2" min. to 1" | ||
|
|
|
| max. If countertop excedes 1" thickness you must | ||
Place a retaining clip onto |
| request clips for the larger thickness. Part No. | ||||
certain locking tab engages depression in |
| |||||
| unused hole, order Part No. | |||||
on page 3 for correct model. |
|
|
|
|
|
7 9 0 7 6 7 - 1 0 0 | 2 | © A M E R I C A N S T A N D A R D I N C . 2 0 0 2 |