Installation Instructions
SERIN™ | 2064.451 |
WALL MOUNT FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds
Certified to comply with ASME A112.18.1M U.S. Patent No. 5,819,789
M968852 Rev.1.3
To ensure that your installation proceeds
2" MIN. | 3" MAX. | ||
8" | |||
(51mm) | (76mm) MAX. | ||
(203mm) | |||
4" |
| ||
|
| ||
CROSS | (102mm) |
| |
HANDLE |
|
| |
|
| 1" | |
|
| (25mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FINISHED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2" D. |
| |
HOT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| COLD | WALL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (52mm) |
| |||||
|
|
|
| 1/2" NPT INLETS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2" D. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| (54mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (52mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
| 2" MAX. (51mm) MAX. |
|
|
|
|
|
|
|
|
|
|
| FINISHED | |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| WALL | |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (235mm) |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| (32mm) O.D. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Required Tools
|
| Adjustable Wrench | |
|
|
| Plumbers' Putty or |
|
|
| Caulking |
1 | Tubing Cutter | Channel Locks | |
INSTALL VALVE BODY | CAUTION | Turn off hot and cold water | |
| supplies before beginning. |
Determine where the finished wall location will be. This measurement is very important! Note: The
Secure FAUCET BODY (1) to cross brace of wall structure | WALL STUDS |
at required height using two wood screws. |
|
Connect HOT water supply to left VALVE inlet and COLD water |
|
supply to right VALVE inlet. Use pipe sealant or Teflon tape for |
|
all threaded connections. For sweat connections, do not make |
|
sweat connections directly to valve body. Damage to seals and |
|
and valve cartridge may occur. |
|
Turn valves to off position. Turn hot and cold supplies on and |
|
check fitting connections for leaks . |
|
Complete wall construction. |
|
| Pipe Wrench |
Teflon Tape | Flat Blade Screwdriver |
CROSS BRACE
1 | WOOD SCREWS |
|
MAX
W
A
L
L
M
I
N
1 -
5 / 8"DEEP
MAX
W
A
L
L
M
I
N
1 - 5 / 8"DEEP
HOT 16"
COLD