American Standard SERIES 7193 installation instructions Installation Instructions

™

Installation

Instructions

LAKELAND™ KITCHEN SINKS

SERIES 7193

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin.

AMERICAST® BRAND

SELF RIMMING

Certified to comply with ANSI A112.19.4.M U.S. Patent No. 4,664,982

Other patents pending. CAN/C.S.A. B-45

Observe local plumbing and building codes.

BEFORE YOU BEGIN...

Unpack new sink and inspect carefully for damage. Replace the sink in its original packing carton to protect it until you are ready to begin installation.

Recommended Tools & Materials

Silicone Sealant	Drill
Putty Knife	Basin Wrench
Pipe Wrench	Saber Saw
Channel Locks	Tubing Cutter
Phillips Screwdriver	Tape Measure
Regular Screwdriver	Hacksaw
Adjustable Wrench	Mineral Spirits

Refer to American Standard roughing-in information for

specific dimensions for each model.

CUTOUT DIMENSIONS FOR SINKS:

Below are the dimensions needed to determine the cutout size for your installation. Select the correct diagram for your application and refer to the instructions below.

Locate and mark center lines of sink on countertop.

Provide proper clearance under the countertop for the faucet supply lines and the structural parts of the cabinet.

By using the diagrams below and measuring your sink, draw the outline of the sink onto the countertop. This is not the cutting outline.

Refer to the diagram for your sink and draw a line the required distance in from the sink outline. Cut on this line.

COUNTERTOP CUTOUT FOR

COUNTERTOP CUTOUT FOR

NEW INSTALLATIONS

UNDERCOUNTER INSTALLATIONS

33"

27-3/8"

(838mm)

1" R (25mm) TYP.

(695mm)

CUTOUT

22"

2-5/16" R (19mm) TYP.

1-5/8" (16mm)

16-7/8"

(559mm)

(429mm)

SINK

SUPPORT

OUTLINE

5/8"

CLIPS

CUTTING LINE

(16mm)

LAKELAND SINGLE BOWL

COUNTERTOP MOUNTED FAUCET

MODEL 7193 UNDER COUNTER MOUNT

MODEL 7193 SELF RIMMING

LAKELAND SINGLE BOWL

COUNTERTOP CUTOUT FOR

REPLACEMENT INSTALLATIONS

33"

29-1/2"

(749mm)

(838mm)

CUTOUT

1" R (25mm) TYP.

3/4" R (19mm) TYP.

22"

20-1/2"

5/8" to 1-5/8"

(559mm)

(521mm)

(16 to 41mm)

SUPPORT

SINK

5/8"

OUTLINE

CLIPS

CUTTING LINE

(16mm)

SINK MOUNTED FAUCET

LAKELAND SINGLE BOWL

MODEL 7193 UNDER COUNTER MOUNT

MODEL 7193 SELF RIMMING

LAKELAND SINGLE BOWL

CAUTION:

1.Recommended Minimum Countertop Thickness Wood 19mm (3/4") Marble and Solid Surface 12mm (1/2")

2.Prior to cutting countertop ensure that the faucet shank has sufficient length to attach the mounting nut after the shank goes through both the countertop and the sink deck. The deck is 10mm (3/8") thick.

NOTE: Undercounter Installations of sinks should be done by trained and experienced installers due to the materials (such as marble, hard synthetics, etc.). Contact your countertop distributor for best method of cutting the opening.

IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN

THE RANGE OF TOLERANCES ESTABLISHED BY A . N . S . I . AND C . S . A . STANDARDS .

©AMERICAN STANDARD INC . 2005

791393 - 100 Rev . A