INSTALLATION INSTRUCTIONS
For These Two-Piece Toilets:
Ellisse 2184 | Deco 2059 |
Heritage 2176 | Cadet III 13L 2650/2660 |
Baby Devoro 2315 | Sonoma 2454 |
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE! NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife | Regular Screwdriver | Adjustable Wrench | Sealant | Tape Measure |
|
| ||
Hacksaw | Wax Ring/Gasket | Flexible Supply Tube | Closet Bolts | Carpenters Level | E | |||
1 | REMOVE OLD TOILET |
|
|
|
|
| S | |
|
|
|
|
|
| |||
a. | Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl. | U | ||||||
b. | Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply! |
|
| |||||
c. | Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. | E | ||||||
d. | Remove closet bolts from flange and clean away old wax, putty, etc. from base area. |
| ||||||
|
| |||||||
| NOTE: Mounting surface must be clean and level before new toilet is installed! |
|
| R | ||||
|
|
|
|
|
|
|
| |
2 |
| 3 |
| 4 |
| U | ||
|
|
| T | |||||
| NOTE: Distance from wall to closet flange centerline must |
|
|
|
| |||
| be as listed below: |
|
|
| SEALANT | WAX RING | U | |
|
| For 4110 Tanks: A = 10" (254mm) |
|
|
| |||
| FINISHED WALL | For 4114 Tanks: A = 14" (356mm) |
|
|
|
|
|
|
|
|
| CLOSET FLANGE |
|
| F | ||
|
| For all other Tanks: A = 12" (305mm) |
|
| ||||
|
|
|
|
|
| |||
|
|
|
|
| A |
|
| R |
|
|
|
| CLOSET BOLTS |
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| O |
|
| SUPPLY |
|
|
|
|
| F |
|
| AS |
|
|
| INSTALL WAX SEAL |
| |
|
|
|
|
|
|
| ||
|
| REQ'D. |
|
|
|
|
|
| INSTALL CLOSET BOLTS | Invert toilet on floor (cushion to |
|
| prevent damage), and install wax | E | |
| Install closet bolts in flange channel, | ||
| ring evenly around waste flange | ||
| turn 90° , and slide into place 6" |
| |
| (152 mm) apart and parallel to wall. | (horn), with tapered end of ring | V |
| facing toilet. Apply a thin bead of | ||
|
|
| |
A | FINISHED | sealant around toilet base. | A |
FLOOR |
| ||
|
| ||
|
|
| S |
5 |
| 6a |
|
| NUT | INSTALL TOILET | |
|
|
| |
| TAPERED | Position toilet squarely to wall | |
| and, with a rocking motion, press | ||
| WASHER | ||
|
| bowl down fully on wax ring and | |
|
| flange. Alternately tighten nuts | |
|
| until toilet is firmly seated on floor. | |
| CLOSET |
|
|
| BOLT |
|
|
|
| ! | CAUTION: |
| FLANGE | DO NOT OVERTIGHTEN NUTS | |
|
| OR BASE MAY BE DAMAGED! | |
POSITION TOILET ON FLANGE | CLOSET FLANGE |
| |
a. | Unplug floor waste opening and install toilet on closet flange |
| |
|
| ||
| so bolts project through mounting holes. |
|
|
b. | Loosely install retainer washers and nuts. Side of washers |
|
|
| marked "THIS SIDE UP" must face up! |
|
|
Saniwares
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A m e r i c a n S t a n d a r d I n c . 2 0 0 0
730513 - 100 REV . D