6b | INSTALL BOLTS AND CAPS | |
| BOLT CAP |
|
|
| Ellisse 2184 |
| CLOSET | Baby Devoro 2315 |
| Deco 2059 | |
| BOLT | Cadet III 13L 2650/2660 |
|
| |
|
| Sonoma 2454 |
WASHER NUT
a.Install caps on washers. (If necessary, cut bolt height to size before installing caps.)
b.Smooth off the bead of sealant around base. Remove excess sealant.
COVER | COVER | HERITAGE 2176 |
MTG. CLIP |
|
|
|
| CLOSET |
|
| BOLT |
WASHER | NUT |
|
|
|
a.Press covers over mounting clips. (If necessary, cut bolt height to size before installing covers.)
b.Smooth off the bead of sealant around base. Remove excess sealant.
7a
For Tanks/Bowls using Speed Connect System (Tank mounting bolts
TANK MTG. | RUBBER | |
GASKET | ||
BOLTS PRE- | ||
| ||
INSTALLED |
|
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washers and nuts.
b.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
!CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
7b
For all other Tanks/Bowls
RUBBER
WASHER
RUBBER
TANK MTG. 
GASKET BOLTS
WASHER
NUT
INSTALL TANK
a.Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening.
b.Insert tank mounting bolts and rubber washers from inside tank, through mounting holes, and secure with metal washers and nuts.
c.With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
!CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
8 | INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. |
|
9a | Before continuing, determine the type of water supply connecation you have from |
| the chart below and use the appropriate assembly parts required to properly |
| reconnect the water supply. DO NOT use plumber's putty to seal these fittings. |
METAL/COPPER | METAL FLANGED | METAL SPIRAL | VINYL/BRAIDED | |||
FLARED TUBING | TUBING | TUBING | CONNECTOR | |||
LOCK NUT | LOCK NUT | LOCK NUT | LOCK NUT | |||
CONE | EXISTING | EXISTING | COUPLING | |||
WASHER | ||||||
WASHER | CONE | NUT | ||||
COUPLING | EXISTING | WASHER |
| |||
|
| |||||
COUPLING | COUPLING |
| ||||
NUT |
| |||||
| NUT | NUT |
| |||
WATER | WATER | WATER | WATER | |||
These parts must be used as | Use existing | Use existing spiral | Captive cone | |||
illustrated to insure | coupling nut | cone washer. | washers already | |||
connection. Use of existing | and washer. | Fluidmaster cone | included. No | |||
coupling nut may result in |
|
|
| washer may not | additional washers | |
water leakage. Water supply |
|
|
| seal completely on | needed. | |
tube or pipe must extend at |
|
|
| spiral type supply |
| |
least 1/2" inside threaded |
|
|
| line. |
| |
shank of valve (does not apply |
|
|
|
|
| |
to flanged tubing). |
|
|
|
|
| |
|
|
|
| |||
CAUTION: DO NOT USE |
|
| CAUTION: Overtightening of | |||
CONE WASHER WITH |
|
| LOCK NUT or COUPLING NUT | |||
|
| could result in breakage and | ||||
PLASTIC SUPPLY LINE. |
|
| potential flooding. | |||
|
|
|
|
|
| |
9b
With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight. DO NOT OVERTIGHTEN.
- 2 - | 730513 - 100 REV . D |
|
