3 BACK TO BACK INSTALLATION
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should butt up against top of casting. Reassemble FIXATION RING (4) and CARTRIDGE (1).
| 4 3 9 | LARGE OUTLET |
| 1 | 2 |
|
| 5 |
8 | 6 |
|
5 | INLETS | |
|
|
7
ROTATE 180˚
BACK TO BACK INSTALLATION
4 ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the
amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, you need to adjust the setting on the HOT LIMIT SAFETY STOP (1).
Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1).
Pull forward and rotate counterclockwise one number to limit hot water temperature. Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1) for indication.
|
| 579 |
|
| |
| 3 | 11 | 3 |
| |
1 |
|
| 1 | ||
0 |
|
|
|
| |
|
|
|
|
| 5 |
|
|
|
|
| 1 |
2
3
5
1
3
4
2
|
|
|
|
|
| 1 |
|
|
|
|
|
| 5 |
|
|
|
|
|
| 1 |
|
|
|
|
|
| 3 |
|
|
|
|
| 1 | 1 |
|
|
|
| 9 |
| |
|
|
| 7 |
|
| |
|
| 5 |
|
|
| |
| 3 |
|
|
|
| |
1 |
|
|
|
|
| |
|
|
|
|
|
|
4
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
5
|
|
|
|
|
| 1 |
|
|
|
|
|
| 5 |
|
|
|
|
|
| 1 |
|
|
|
|
|
| 3 |
|
|
|
|
| 1 | 1 |
|
|
|
| 9 |
| |
|
|
| 7 |
|
| |
|
| 5 |
|
|
| |
| 3 |
|
|
|
| |
1 |
|
|
|
| 1 | |
|
|
|
|
| ||
|
|
|
|
|
|
| 5 | TEST INSTALLED FITTING |
|
|
|
| |
Turn VALVE (1) "off". |
| ||
| With HANDLE (1) in "off" position, turn on water supplies and check all connections | 3 | |
|
| for leaks. |
|
Operate HANDLE (1) and flush water lines thoroughly. Pull DIVERTER (2) up and check |
| ||
|
| SHOWER (3) for proper operation. |
|
Check SPOUT (4) and SHOWER (3) connections for leaks. | 1 | ||
|
|
|
2
4
6 | EverClean™ Finish Care Instructions |
|
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
M968285 R e v. 1 . 1
