![](/images/new-backgrounds/1132117/13211715x1.webp)
Technical Specifications
POWER OUTPUTS (per channel, stereo mode)1,2 |
|
| |||
| 2 ch | 2 ch 1kHz | 2 ch 40Hz (1 cycle) | 1 ch 1 kHz | 1 ch 40Hz (1 cycle) |
8 ohms: | 230 watts | 260 watts | 280 watts | 295 watts | 300 watts |
4 ohms: |
| 425 watts | 480 watts | 500 watts | 550 watts |
2 ohms: |
| 560 watts | 780 watts | 750 watts | 900 watts |
|
|
|
| ||
POWER OUTPUTS (mono mode)1,2 |
|
|
| ||
| 1kHz | 40Hz (1 cycle) |
|
| |
16 ohms: | 460 watts | 520 watts | 560 watts |
|
|
8 ohms: |
| 850 watts | 960 watts |
|
|
4 ohms: |
| 1120 watts | 1560 watts |
|
|
|
| ||||
FREQUENCY RESPONSE | +0, | ||||
|
| ||||
TOTAL HARMONIC DISTORTION | Less than .25%, 20Hz - 20kHz @230 W / channel @ 8 ohms | ||||
|
|
| |||
SLEW RATE1 |
| 30 volts / microsecond (stereo mode), 60 volts / microsecond (mono mode) | |||
|
|
| |||
SIGNAL TO NOISE RATIO1,2 | Greater than |
| |||
|
| ||||
INPUT TYPE AND IMPEDANCE | Transformerless electronically balanced, 20K actual load impedance. Suitable for Low or | ||||
|
| ||||
|
|
|
| ||
INPUT SENSITIVITY | 1.5 V RMS for 230 Watts / 8 ohms |
|
| ||
|
| ||||
LOAD IMPEDANCE | Stereo Mode: 2 ohms or greater; Bridged Mono Mode: 4 ohms or greater | ||||
|
|
|
| ||
DAMPING FACTOR1 | Typical 250 (1kHz, 8 ohms) |
|
| ||
|
| ||||
OUTPUT CONNECTIONS | 1/4” phone jack*, plus Speakon® jacks each channel; Speakon® jack for Mono Bridge/Biamp | ||||
|
| ||||
PROTECTION CIRCUITRY | Short circuit, RF burnout, overtemp, turn on/off transient and DC protection, Speaker protection | ||||
|
| relays, |
| ||
|
|
|
| ||
COOLING |
| Forced air fan cooling, rear intake, front exhaust |
| ||
|
|
|
| ||
POWER REQUIREMENTS | 115VAC 60Hz, 880VA |
|
| ||
|
| 100/110VAC 50/60Hz, 880VA |
|
| |
|
| 230VAC, 50/60Hz, 880VA |
|
| |
|
|
|
| ||
CIRCUIT BREAKER | 10 amp (mains) |
|
| ||
|
|
| |||
SIZE AND WEIGHT | 19” W x 5.25” H x 12.5” D; 33 lbs. | 483mm x 133mm x 317mm; 15Kg. | |||
|
|
|
| ||
1typical performance 2@115 VAC 60Hz |
|
| *NOTE: 1/4” jacks not available in some areas. |
Ampeg reserves the right to change specifications without notice.
Ampeg is proudly Made in America. ©1996 SLM Electronics, 1400 Ferguson Avenue, St. Louis, MO 63133 U.S.A.
P/N