AmpliVox SW227 BATTERY installation / SET-UP, SW225 Voice Projector, SW225 Wireless Mic Set up

BATTERY installation / SET-UP:

Install Power supply in all componenets:

important! Do not mix battery types or attempt to recharge alkaline batteries. Equipment dammage, safety hazard or fire could result. Remove batteries if the unit is not going to be used for long periods of time to prevent leakage.

SW225 Wireless Voice Projector: Runs on AC power or battery power. The battery carriage holds 10 D-cell alkaline batteries or our S1465 NiCad battery pack (requires S1460 AC adapter to recharge). Or run on a 12 Volt DC adapter (automotive cigarette lighter plug-in, not included).

S1204-70 Wireless Powered Speaker: Runs on AC power or battery power. The battery carriage holds 10 D-cell alkaline batteries or our S1465 NiCad battery pack (requires S1460 AC adapter to recharge). Or run on a 12 Volt DC adapter (automotive cigarette lighter plug-in, not included).

For both the 1204-70 and SW225: Loosen four thumbscrews and remove battery door from back of speaker. Remove battery carriage. Insert 10 D-cell alkaline batteries, observing polarity, or replace with fully charged S1465 NiCad battery pack. Carefully replace the battery carriage. Reposition battery door and fasten the thumbscrews.

S1670 Transmitter Power Supply: Requires one 9-Volt battery or a 9-Volt AC adapter (not supplied). Remove battery door on back of transmitter. insert one new 9 volt alkaline battery, observing polarity, and replace the door.

Lapel & Headset Mic Battery Installation: Requires one 9-Volt battery or a 9-Volt AC adapter (not supplied). Remove battery door on back of

SW225 Voice Projector

transmitter. insert one new 9 volt alkaline battery, observing polarity, and replace the door.

set-up wireless transmitter for the S1204-70 speaker:

PLEASE NOTE: YOU HAVE TWO SEPERATE TRANSMITTERS. ONE IS FOR THE SPEAKER AND THE OTHER IS FOR THE MICROPHONE.

SPEAKER = BEGINS WITH 169 MIC = BEGINS WITH 171

Connect provided cable from the MIC INPUT JACK on the S1670 transmitter (labled 169) into the LINE OUT JACK (*see image on next page) on the Amplifier on the SW225 Voice Projector. Turn SW225 Amplifier ON. Turn S1670 transmitter ON. Make sure frequencies MATCH. Turn S1204-70 Speaker Amplifier ON. The red light should illuminate.

NOTE: If for any reason the S1670 transmitter frequency is changed from its factory set position A please reset to A. The internal wireless receiver is preset to A.

NOTE: The frequencies used by the S1204-70 Speaker and the S1670 transmitter are not on clear channels adn may be used by other devices. If the unit receives interference and if you are unable to use the S1670 transmitter, connect the LINE OUT on the SW225 Voice Projector to the S1204-70 LINE IN using a 3.5mm miniplug cable. Turn the volume control on the S1204-70 speaker completely down.

SW225 Wireless Mic Set up:

Plug headset or lapel microphone into transmitter labled with 171, select A or B frequency, turn power switch ON. A red light should come on. Turn SW225 on with the main power switch. When the power switch is in the ON position, the red light will be on. Turn wireless receiver power switch on and select matching frequency to the mic transmitter,

s1204-70 WIRLESS POWERED SPEAKER

S1670

TRANSMITTER

WITH CABLE

AMPLIFIER	BATTERY
		HANDLE
	CONTROL	DOOR PANEL
	PANEL

transmitter battery installation

RIBBON FOR		PLEASE NOTE:
BATTERY REMOVAL		YOU HAVE TWO
		SEPERATE
		TRANSMITTERS
		ONE IS FOR THE
		SPEAKER AND THE
		OTHER IS FOR THE
	9V DC ALKALINE	MICROPHONE.
			HANDLE	AMPLIFIER	BATTERY
	BATTERY	SPEAKER = 169
				CONTROL	DOOR PANEL
	BATTERY COVER	MIC = 171		PANEL

SW227

2