Quick Start Guide
AXR-IRSM+ Swivel-Mount Remote IR Receiver
Overview
The
Note: The
Circuit board
assembly 
Housing 
Swivel mount base
IR Data
LED IR Sensor
IR Data LED
IR
Sensor
|
|
|
|
|
| IR SNSR |
|
|
|
|
|
|
| IR SNSR |
|
|
|
|
|
| 38/455 |
|
|
|
|
|
|
| 38/455 |
|
|
|
|
|
| kHz |
|
|
|
|
|
|
| kHz |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
| Setting for 38 kHz |
| Setting for 455 kHz | |||||||||
FIG. 3 Receive frequency jumper settings
Note: The unit will not operate with one set of pins configured for 38 kHz and the other set of pins configured for 455 kHz.
•To receive 455 kHz (default setting), position both jumpers on pins 1 and 2 (away from the edge of the circuit boards).
•To receive 38 kHz, position both jumpers on pins 2 and 3 (near the edge of the circuit boards).
Setting the AXlink Device Number
1.Locate the
2.Set the device address according to the DIP switch values shown below.
Switch | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
Value 1 2 4 8 16 32 64 128
The device number is set by the total value of DIP switch positions that are ON (down). The Axcess software program in your system typically uses device numbers 128 through 255 for the panels.
As an example, the DIP switch in FIG. 4 defines device number 129 (1+128=129).
FIG. 1 AXR-IRSM+ swivel-mount IR receiver
AXR-IRSM+ Specifications
Dimensions (HWD): | 3.30" x 2.00" x 2.6" (83.80 mm x 50.80 mm x 66.00 mm) |
|
|
Receive Frequencies: | 38 / 455 kHz |
|
|
Enclosure | Neutral |
|
|
Mounting: | May be used without the wall bracket for flush mounting. |
| Comes with full set of mounting screws and wall anchors. |
|
|
Weight: | 5.6 oz (174 grams) |
|
|
Power Consumption: | 35 mA |
|
|
Wiring and Installation
Set the receive frequency, AXlink device number and IR validation level before installing the
FIG. 2 illustrates the location of key components on the AXR-IRSM+ circuit board.
IR Validation
Jumper Pins
AXlink Device | AXlink |
DIP Switch | Connector |
Receive Frequency
Jumper Pins
FIG. 2 Location of key components on the AXR-IRSM+ circuit board
Setting the Receive Frequency
FIG. 4 Example Device DIP Switch set to 129
Note: If you later change the device number, remove and reconnect the AXlink connector to enter the new device number into memory.
Sensor IR Validation Level
The IR validation level is set on the receiving device (such as an
Setting the IR Validation Level
An IR transmitter must send repetitions of data for the receiver to accept it as valid data. In some installations, a light wall color or other physical condition may interfere with the sensor's or receiver's ability to sense the transmitted signal. The signal may reflect or bounce and become distorted. The receivers can be set to use either two or three repetitions of sequential signals to validate and accept the signal data.
Perform the following steps to set the receiver's IR validation level.
1.Locate the IR Validation jumper pins (J1) (FIG. 5) on the circuit board (FIG. 2).
| 2 | 3 |
|
|
|
| 2 | 3 |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| J1 |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| J1 |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting for 2 validations | Setting for 3 validations | |||||||||||||||||
FIG. 5 IR validation jumper pin settings
2.Position the IR validation jumper (FIG. 5) to select the number of valid IR data repetitions to be accepted:
•Position the jumper at 2 to have the unit validate 2 sequential signals.
•Position the jumper at 3 to have the unit validate 3 sequential signals.
Wiring the IR Sensors and Receivers
Use the set of jumper pins on the corner of the circuit board to set the receive frequency. FIG. 3 illustrates the configuration of the jumpers.
The
