AMX specifications NXC-IRS4 FG2023 Specifications, NXC-IRS4 Pinouts, Signals, and Functions

Installation Guide

NXC-IRS44-Port IR/S Card, 4 IR/S and 4 Inputs

NetLinx Control Cards and NetModules

NetLinx Control Cards can be installed in either the NXF CardFrame, NI-4000, or NetModules. This document provides basic specifications and wiring information for the NetLinx Control cards. For detailed information on the cards, refer to the NetLinx CardFrame, Control Cards, and NetModules Instruction Manual.

NXC-IRS4 4-Port IR/S Control Card

The NXC-IRS4 4-Port IR/S Control Card provides four IR/Serial output control ports with LED status feedback. Each port in the NXC-IRS4 stores programmed commands for IR- or serial-controlled devices.

Specifications

NXC-IRS4 (FG2023) Specifications

Power	110 mA @ +12 VDC power for sensors
Operation:	•	IR 1-4: 4 IR/Serial control ports
	•	Input 1-4: 4 input ports for closure or 0-5 VDC sensing, 200 mA
Memory	32K of IR memory shared between four ports.
IR Frequency range	Support of high-frequency carriers up to 1.14 MHz.
Status LEDs:	Red LED shows IR transmission activity / yellow LED shows input
	status activity (2 LEDs per channel). LEDs light to indicate ON
	status:
	•	LED 1: Channel 1 Input (yellow)
	•	LED 2: Channel 1 IR Out (red)
	•	LED 3: Channel 2 Input (yellow)
	•	LED 4: Channel 2 IR Out (red)
	•	LED 5: Channel 3 Input (yellow)
	•	LED 6: Channel 3 IR Out (red)
	•	LED 7: Channel 4 Input (yellow)
	•	LED 8: Channel 4 IR Out (red)
Connections/wiring:	•	Two 2-pin 3.5 mm captive-screw terminals
	• Two CC-NIRC IR Emitters
Models:	•	NXC-IRS4 4-Port IR/S Card
	•	NXM-IRS4 4-Port IR/S NetModule
DEVICE_ID:	$0108

Pinouts, Signals, and Functions

NXC-IRS4 Pinouts, Signals, and Functions

Pin	Signal	Function	Pin	Signal	Function
1	GND	Signal ground	10	Input #1	Logic input
2	Output #1	IR data	11	Input #2	Logic input
3	GND	Signal ground	12	Input #3	Logic input
4	Output #2	IR data	13	Input #4	Logic input
5	GND	Signal ground	14	Power	+12 VDC
6	Output #3	IR data	15	---------------	no connection
7	GND	Signal ground	16	---------------	no connection
8	Output #4	IR data	17	---------------	no connection
9	GND	Signal ground	18	---------------	no connection
			19	---------------	no connection
			20	---------------	no connection

NXC-IRS4 Channel Assignments

The IRS4 channel settings listed in the following table set the IR output channels. The NXC-IRS4 can process up to two IR or serial device channel setting commands simultaneously. If more than two device commands are sent simultaneously, only the first two devices receive the commands.

NXC-IRS4 Channel Assignments

Channel Description

1-255	Generates the IR or serial command assigned to that channel.
1-199	Provides intelligent feedback; if a channel with no IR command is turned on,
	the card will turn that channel off.
Ports 1-4 Generates PUSH and RELEASE statements corresponding to the state of
	inputs 1 - 4. A contact closure to GND is reported as a PUSH.
	• The PUSH and RELEASE channel is 255.
	•	Channel reporting status is 255.
	•	Channel 255 changes are disabled after receipt of the ’PON’ command.

Programming Information

NXC-IRS4 SEND_COMMANDS

CAROFF	Syntax:
Disable the IR carrier		SEND_COMMAND <DEV>,"'CAROFF'"
signal until a 'CARON'	Example:
command is received.		SEND_COMMAND IR_1,"'CAROFF'"
	Stops transmitting IR carrier signals to the IR_1 port.
CARON	Syntax:
Enable the IR carrier		SEND_COMMAND <DEV>,"'CARON'"
signals (default).	Example:
		SEND_COMMAND IR_1,"'CARON'"
	Starts transmitting IR carrier signals to the IR_1 port.
CH	All channels below 100 are transmitted as two digits. If the IR
Send IR pulses for the	code for ENTER (function #21) is loaded, an Enter will follow
selected a channel.	the number. If the channel is greater than or equal to (>=) 100,
	then IR function 127 or 20 (whichever exists) is generated for
	the one hundred digit. Uses 'CTON' and 'CTOF' times for pulse
	times.
	Syntax:
		SEND_COMMAND <DEV>,"'CH',<Number>"
	Channel number = 0 - 199.
	Example:
		SEND_COMMAND IR_1,"'CH',18"
	The NXC-IRS4 performs the following:
	•	Transmits IR signals for 1 (IR code 11). The transmit time is
		set with the CTON command.
	•	Waits until the time set with the CTOF command elapses.
	•	Transmits IR signals for 8 (IR code 18).
	•	Waits for the time set with the CTOF command elapses. If
		the IR code for Enter (IR code 21) is programmed, the IRS4
		performs the following steps.
	•	Transmits IR signals for Enter (IR code 21).
	•	Waits for the time set with the CTOF command elapses.
CP	Syntax:
Halt and Clear all active		SEND_COMMAND <DEV>,"'CP',<code>"
or buffered IR com-	Code = IR port's channel value 0 - 252 (253 - 255 reserved).
mands, and then send a	Example:
single IR pulse. Set the		SEND_COMMAND IR_1,"'CP',2"
Pulse and Wait times
	Clears the active/buffered commands and pulses IR_1 port's
with the 'CTON' and
	channel 2.
'CTOF' commands.
CTOF	This command sets the delay time between pulses generated
Set the duration of the	by the 'CH' or 'XCH' send commands in tenths of seconds.
Off time (no signal)	Syntax:
between IR pulses for		SEND_COMMAND <DEV>,"'CTOF',<time>"
channel and IR function	Time = 0 - 255. Given in 1/10ths of a second. Default is 5
transmissions.	(0.5 sec).
Off time settings are	Example:
stored in non-volatile		SEND_COMMAND IR_1,"'CTOF',10"
memory.
	Sets the Off time between each IR pulse to 1 second.
CTON	This command sets the pulse length for each pulse generated
Set the total time of IR	by the 'CH' or 'XCH' send commands in tenths of seconds.
pulses transmitted and is	Syntax:
stored in non-volatile		SEND_COMMAND <DEV>,"'CTON',<time>"
memory.	Time= 0 - 255. Given in 1/10ths of a second. Default is 5
	(0.5 sec).
	Example:
		SEND_COMMAND IR_1,"'CTON',20"
	Sets the IR pulse duration to 2 seconds.
GET MODE	The port responds with: <port #> <mode>,<carrier>,<io link
Poll the IR/Serial port's	channel>.
configuration parame-	Syntax:
ters and report the active		SEND_COMMAND <DEV>,"'GET MODE'"
mode settings to the	Example:
device requesting the		SEND_COMMAND IR_1,"'GET MODE"
information.	The system could respond with:
		PORT 4 IR,CARRIER,IO LINK 0
IROFF	Syntax:
Halt and Clear all active		SEND_COMMAND <DEV>,"'IROFF'"
or buffered IR commands	Example:
being output on the		SEND_COMMAND IR_1,"'IROFF"
designated port.	Immediately halts and clears all IR output signals on the IR_1
	port.