AMX NXC-IRS4 SENDCOMMANDS Cont, Set Io Link, LINK command, Set Mode, Xchm, Ptof, Pton, 93-2023

NXC-IRS4 SEND_COMMANDS (Cont.)		SET IO LINK	Syntax:
		Link an IR or Serial port	SEND_COMMAND <DEV>,"'SET IO LINK <I/O
POD	Channel 255 changes are enabled.	to a selected I/O channel	number>'"
Disable previously active	Syntax:	for use with the 'DE',	I/O number = 1 - 4. An I/O channel to 0 disables the I/O link.
'PON' (power on) or	SEND_COMMAND <DEV>,"'POD'"	'POD', 'PON', and 'POF'	Example:
'POF' (power off) com-	Example:	commands.	SEND_COMMAND IR_1,"'SET INPUT LINK 1'"
mand settings.	SEND_COMMAND IR_1,"'POD"
			Sets the IR_1 port link to I/O channel 1. The IR port uses the
This command is used in
	Disables the 'PON' and 'POF' command settings on the IR_1		specified input as power status for processing PON and POF
conjunction with the I/O
	device.		commands.
Link command.
			Note: This command is included for older programs only. The
POF	If at any time the IR sensor input reads that the device is ON		Input port is not an I/O. No output functions are available.'SET
Turn OFF a device	(such as if someone turned it on manually at the front panel),		IO LINK' applies the same configuration as the 'SET INPUT
connected to an IR port	IR function 28 (if available) or IR function 9 is automatically		LINK' command.
based on the status of	generated in an attempt to turn the device back OFF. If three
		SET MODE	Syntax:
the corresponding I/O	attempts fail, the IR port will continue executing commands in
		Set the IR/Serial ports for	SEND_COMMAND <DEV>, 'SET MODE <mode>'"
Link input.	the buffer. If there are no commands in the buffer, the IR port
	will continue executing commands in the buffer and trying to	IR or Serial-controlled	Mode = IR or Serial.
	turn the device OFF until a 'PON' or 'POD' command is	devices connected to a	Examples:
	received.	CardFrame or NetMod-	SEND_COMMAND IR_1,"'SET MODE IR'"
	If the IR port fails to turn the device OFF, a PUSH and	ule.	Sets the IR_1 port to IR mode for IR control.
		Sets an IR port to either
	RELEASE is made on channel 254 to indicate a power failure
	error. You can only use the 'PON' and 'POF' commands when	IR or Serial mode.
	an IR device has a linked I/O channel. Channel 255 changes
		SP	You can use the 'CTON' to set pulse lengths and the 'CTOF' for
	are disabled after receipt of this command. You can only use
		Generate a single IR	time off between pulses.
	the PON and POF commands when an IR device has a linked
		pulse.	Syntax:
	I/O channel.
			SEND_COMMAND <DEV>,"'SP',<code>"
	Syntax:
	SEND_COMMAND <DEV>,"'POF'"		Code = IR code value 1 - 252 (253-255 reserved).
			Example:
	Example:
			SEND_COMMAND IR_1, "'SP',25"
	SEND_COMMAND IR_1,"'POF'"
			Pulses IR code 25 on IR_1 device.
	Sends power down IR commands 28 (if present) or 9 to the
	IR_1 device.	XCH	Syntax:
PON	If at any time the IR sensor input reads that the device is OFF	Transmit the selected	SEND_COMMAND <DEV>,"'XCH <channel>'"
Turn ON a device	(such as if one turned it off manually at the front panel), IR	channel IR codes in the	Channel = 0 - 999.
connected to an IR port	function 27 (if available) or IR function 9 is automatically gener-	format/pattern set by the	Example:
based on the status of	ated in an attempt to turn the device back ON. If three attempts	'XCHM' send command.	For detailed usage examples, refer to the 'XCHM' command.
the corresponding I/O	fail, the IR port will continue executing commands in the buffer
		XCHM	Syntax:
Link input.	and trying to turn the device On.
	If there are no commands in the buffer, the IR port will continue	Changes the IR output	SEND_COMMAND <DEV>,"'XCHM <extended
	trying to turn the device ON until a 'POF' or 'POD' command is	pattern for the 'XCH'	channel mode>'"
	received. If the IR port fails to turn the device ON, a PUSH and	send	Extended channel mode = 0 - 4.
	RELEASE is made on channel 254 to indicate a power failure	command.	Example:
	error.		SEND_COMMAND IR_1,"'XCHM 3'"
	You can only use the 'PON' and 'POF' commands when an IR		Sets the IR_1 device's extended channel command to mode 3.
	device has a linked I/O channel. Channel 255 changes are		Mode 0 Example (default): [x][x]<x><enter>
	disabled after receipt of this command.
			SEND_COMMAND IR_1,"'XCH 3'"
	Syntax:
			Transmits the IR code as 3-enter.
	SEND_COMMAND <DEV>,"'PON'"
			SEND_COMMAND IR_1,"'XCH 34'"
	Example:
			Transmits the IR code as 3-4-enter.
	SEND_COMMAND IR_1,"'PON'"
			SEND_COMMAND IR_1,"'XCH 343'"
	Sends power up IR commands 27 or 9 to the IR_1 port.
			Transmits the IR code as 3-4-3-enter.
PTOF	This command also sets the delay between pulses generated		Mode 1 Example: <x> <x> <x> <enter>
Set the time duration	by the 'PON' or 'POF' send commands in tenths of seconds. It		SEND_COMMAND IR_1,"'XCH 3'"
between power pulses in	also sets the delay required after a power ON command before		Transmits the IR code as 0-0-3-enter.
.10-second increments.	a new IR function can be generated. This gives the device time		SEND_COMMAND IR_1,"'XCH 34'"
Time is given in 1/10ths	to power up and get ready for future IR commands. It also sets
			Transmits the IR code as 0-3-4-enter.
of a second.	the delay required after a power ON command before a new IR
This time increment is	function can be generated. This gives the device time to power		SEND_COMMAND IR_1,"'XCH 343'"
	up and get ready for future IR commands.		Transmits the IR code as 3-4-3-enter.
stored in permanent
memory.	Syntax:		Mode 2 Example: <x> <x> <x>
	SEND_COMMAND <DEV>,"'PTOF',<time>"		SEND_COMMAND IR_1,"'XCH 3'"
	Time = 0 - 255. Default is 15 (1.5 seconds).		Transmits the IR code as 0-0-3.
	Example:		SEND_COMMAND IR_1,"'XCH 34'"
	SEND_COMMAND IR_1,"'PTOF',15"		Transmits the IR code as 0-3-4.
	Sets the time between power pulses to 1.5 seconds for the		SEND_COMMAND IR_1,"'XCH 343'"
	IR_1 device.
			Transmits the IR code as 3-4-3.
PTON	This command also sets the pulse length for each pulse gener-		Mode 3 Example: [[100][100]…] <x> <x>
Set the time duration	ated by the 'PON' or 'POF' send commands in tenths of sec-		SEND_COMMAND IR_1,"'XCH 3'"
between power pulses in	onds.		Transmits the IR code as 0-3.
.10-second increments.	Syntax:		SEND_COMMAND IR_1,"'XCH 34'"
Time is given in 1/10ths	SEND_COMMAND <DEV>,"'PTON',<time>"		Transmits the IR code as 3-4.
of a second.	Time = 0 - 255. Default is 5 (0.5 seconds).
			SEND_COMMAND IR_1,"'XCH 343'"
This time increment is	Example:
			Transmits the IR code as 100-100-100-4-3.
stored in permanent	SEND_COMMAND IR_1,"'PTON',15"
			Mode 4: Mode 4 sends the same sequences as the 'CH'
memory.
	Sets the duration of the power pulse to 1.5 seconds for the
			command. Only use Mode 4 with channels 0 - 199.
	IR_1 device.
SET INPUT LINK	Syntax:
Sets an IR device to link	SEND_COMMAND <DEV>,"'SET INPUT LINK
to an input channel for	<channel>'"
use with 'PON' and 'POF'	Channel = 1 - 4. Setting the channel to 0 disables the link.
commands.	Examples:
The input channel is	SEND_COMMAND IR_1,"'SET INPUT LINK 0'"
used for power sensing	SEND_COMMAND IR_1,"'SET INPUT LINK 1'"
(via a PCS).	Sets the IR_1 port link to I/O channel 1.
	For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).			93-2023	REV: E
	1207
	©2007 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
	AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com