Anritsu MU368060A 6-4

Section 6 AWGN Internal Adder Function

6-4

[6] Output Level

Displays [(noise power for all bands)+(total power for multiplex chan-

nels of W-CDMA modulation wave)]

[7] AWGN

Sets the AWGN internal adder function On/Off. When set to Off, the

MX368041A/B standards apply to all items. When set to On, the

MU368060A, not the MX368041A/B, standards apply.:

•Carrier frequency range

•Number of multiplex channel

•I/Q output signal

•RF output signal

Setting item: On, Off

Initial value: Off

[8] C/N

Sets the ratio between noise power within 3.84 MHz bandwidth and

W-CDMA modulation wave power. Note that this is not the ratio for

noise power of all bands.

Setting range: –30.0 to –20.0 dB (0.2 dB step)

–19.9 to –8.0 dB (0.1 dB step)

Initial value: –20.0 dB

[9] Noise

Displays the ratio between Output Level and noise power within 3.84

MHz bandwidth.

When a warning message "Power under 0dB" is displayed, the dis-

played value does not match with actual output.

[10] Wanted

Displays the ratio between Output Level and W-CDMA modulation

wave power.

When a warning message "Power under 0dB" is displayed, the dis-

played value does not match with actual output.

Contents

Main ii iii Equipment Certificate Anritsu Warranty Anritsu Corporation Contact iv Notes On Export Management Disposing of Product Trademark and Registered Trademark v CE Conformity marking vi C-tick Conformity marking I About This Manual Table of Contents Page Page Page Page 1.2 Product Configuration 1-3 1.2 Product Configuration Page Page Section 2 Storage and Transportation 2-2 2.1 Precautions for Long-term Storage 2.2 Repacking and Transportation 2-3 2.2 Repacking and Transportation Page Page 3-2 3.1 Setting the Parameters Page 3-4 3.1 Setting the Parameters 3-5 3-6. 3.2 Power Accuracy for the Calculated Bandwidth Page Section 4 Sample Measurement 4-2. 4.1 Evaluation Measurement for the Receiver The evaluation measurement procedure for the W-CDMA receiver is de- scribed below. Setup MG3681A + MU368040A + MX368041A/B Two-signal coupler Receiver Wanted signal source Section 5 Sample Calibration 5-1 Section 5 Sample Calibration 5-2 5.1 Calibration of the Output Level 5.1.1 Adjusting the output level for the signal generator 5.1 Calibration of the Output Level 5-3 5.1.2 Adjusting the level at the input connector terminal of the receiver A Noise signal source Section 5 Sample Calibration 5-4 5.1.3 Measuring the level of the outputted noise 5.1 Calibration of the Output Level 5-5 5.1.4 Calibration using the offset setting function of the RF output level Page Section 6 AWGN Internal Adder Function 6-1 6-2 6.1 Product Outline 6.2 Operation When Selecting W-CDMA 6-3 6.2 Operation When Selecting W-CDMA 6.2.1 Main screen 6-4 Page 6-6 6.3 Function Details 6.3 Function Details 6-7 6-8 6.4 Operation When Selecting 1xEVDO 6.4 Operation When Selecting 1xEVDO 6-9 6-10 6.5 Function Details When Selecting 1xEVDO 6.5 Function Details When Selecting 1xEVDO 6-11 Page Section 7 Remote Controls 7-1 7-2 7.1 Device Message List by Function 7.1 Device Message List by Function 7-3 7-4 7.2 Alphabetical Device Message List 7-5 7.2 Alphabetical Device Message List <Example> FREQ 7-6 CALCBW CALCALVL Page I 7-8 IQSRC 7-9 MODE 7-10 7-11 SYS 7-12 7.3 Device Message List for AWGN Internal Adder Functions When Selecting W-CDMA Page 7-14 NOISEADD 7-15 PWRCNR PWRNS Page 7.5 Device Message List for AWGN Internal Adder Functions When Selecting 1xEVDO 7-17 7.5 Device Message List for AWGN Internal Adder Functions When Selecting 1xEVDO Page N 7-19 NOISE N 7-20 NOISECN NOISEPWR Page Page Page 8-2 8.1 Performance Test Caution 8.2 Devices used in Performance Test 8-3 8.2 Devices used in Performance Test 8-4 8.3 RF Output Level Accuracy 8.4 In-band Power Calculation Accuracy 8-5 8.4 In-band Power Calculation Accuracy 8-6. Page Page Appendix A Specifications A-1 Page Appendix B Initial Value List B-1 B Initial Value List Page Appendix C Performance Test Result Sheet C-1 C Performance Test Result Sheet Page Index Index-1 [Alphabetical Order]