3.There are two HDD trays inside the cage. Squeeze the metal clips on each side of a tray and slide it out.

4.Mount your hard drive to the drive tray with the special screws provided. Don’t over-tighten the screws since that could decrease the grommets’ ability to absorb vibration and noise. Note: Always mount the hard drive with the thicker side of the silicone grommets contacting the hard drive.

5.Slide and lock the tray back into the case.

6.Repeat this if you want to mount another hard drive in the upper cage.

7.Slide the cage back to the case and fasten the thumbscrew.

8.Please refer to the power supply installation section to route the power cables to your devices. Once you’ve done so, connect the appropriate power connec- tors to your device.

The Lower HDD Installation.

1.Remove the thumbscrew holding the lower HDD cage.

2.Pull the HDD cage from its position by pulling the ring.

3.You can mount four hard drives inside the cage. They are mounted vertically with silicone grommets on both sides.

4.Mount your hard drive into the drive cage with the special screws provided. (These screws are in the toolbox attached to the back of the upper HDD cage.) Don’t over-tighten the screws since that could decrease the grommets’ ability to absorb vibration and noise. Note: Always mount the HDD with the thicker side of the silicone grommets facing up.

5.Repeat the same procedure for the other drives as necessary.

6.Slide the cage back into the case and fasten the thumbscrew.

7.Please refer to the power supply installation section, to route the power cables to your devices. Once you’ve done so, connect the appropriate power connec- tors to your device.

External 3.5” Drive Installation

There is one external 3.5” drive bay.

1.Carefully remove the plastic drive bay cover and metal plate covering the drive bay.

2.Find the pair of 3.5” drive rails from the box that also contains the top fan spoiler.

3.Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is facing forward and angled outward.

4.Slide the device into the drive bay until you hear it click into place.

5.Please refer to the power supply installation section, to route the power cables to your devices.

6.Connect a small 4-pin connector from the power supply to the male 4-pin connector on the floppy drive.

5.25” Device Installation

There are four 5.25” drive bays in the P180B.

1.Carefully remove the plastic drive bay cover and the metal plate covering the drive bay.

2.Mount the drive rails onto the sides of the 5.25” device. Make sure the metal portion is facing forward and angled outward.

3.Slide the device into the drive bay until you hear it click into place.

4.Mount the other devices accordingly.

4

Page 4 Page 6
Page 5
Image 5
Antec P180B Fan user manual Lower HDD Installation, External 3.5 Drive Installation
Page 4 Page 6

P180B Fan specifications

The Antec P180B is a well-regarded mid-tower case that has been a favorite among PC enthusiasts for its innovative design and efficient cooling capabilities. Renowned for its sleek, modern aesthetics, the P180B features a brushed aluminum front panel and a substantial steel chassis, providing durability and an attractive finish suitable for various settings.

One of the main features of the P180B is its three separate compartments designed for the power supply, hard drives, and motherboard. This compartmentalization not only enhances the overall airflow, but also minimizes noise levels by isolating the power supply and hard drives from the main system components. This innovative layout contributes to a cleaner look and optimized thermal performance.

The P180B is equipped with an advanced cooling system. It comes with three fans: two 120mm rear exhaust fans and one 120mm front intake fan, all equipped with Antec's innovative airflow management technologies. The design also allows for optional additional cooling solutions; users can install up to seven fans, ensuring that air circulation is maximized, effectively keeping the system cool even under heavy loads. The fan speed can be controlled through built-in fan headers on the motherboard, giving users flexibility in balancing performance and noise levels.

Another notable feature of the P180B is its easy-to-access drive bays, supporting up to four 3.5-inch hard drives and a multitude of 5.25-inch devices. The drive bays are tool-less, allowing for quick installation and removal, which is a significant advantage for users who frequently upgrade their components.

Additionally, the P180B supports a wide range of components, including graphics cards up to 12.5 inches in length, making it suitable for high-performance builds. It also supports advanced cooling solutions, including large CPU coolers and even water cooling configurations, further enhancing its versatility as a gaming or workstation case.

The P180B’s design does not skimp on user experience; features like removable dust filters and cable management options simplify maintenance and organization. Overall, the Antec P180B stands out in the market as a case that combines functional design, excellent cooling performance, and aesthetic appeal, making it an ideal choice for both gamers and professionals.
Top Page Image Contents