INSTALLATION
The Network Management Teleservice Card (66124) can be hot- plugged on MGETM GalaxyTM 7000 UPSs. It is not necessary to shutdown the UPS, disconnect the load or restart the UPS.
◗A. Remove the plastic cover of the Minislot.
◗B. Note the MAC address of the card before inserting it.
◗C. Connect the PHONE cable.
◗D. Connect the ETHERNET cable (network already connected).
◗E. Insert and secure the card with the screws.
A |
| E |
|
|
|
|
| UPS | |
|
| UPSData CD | ETHERNET | |
|
|
| SENSOR/RS485 | |
000623001C07 | 000623001C07 |
|
| |
|
| 66124 | ||
|
| C | D | |
B
◗Check the ETHERNET port indications.
◗Wait until the UPS Data LED flashes regularly (approx. two minutes), indicating that card
IP SETTINGS
Once the card has started, proceed as indicated below.
◗Connect one end of the serial cable to the Service port.
◗Connect the other end of the cable to the COM (IOIOI) port of a PC.
◗Run a terminal emulator such as HyperTerminalTM with these settings
Bits per second | Data bits | Stop bits | Flow control |
38400 | 8 | 1 | none |
|
|
|
|
"Echo typed characters locally" option: disabled
◗Press the ↵ key.
◗press the 1 key (Network configuration menu)
◗Type MGEUPS (or mgeups), then press the ↵ key. The main configuration menu is displayed
:
APC by Schneider Electric
NETWORK MANAGEMENT CARD
1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
0 : Exit
Your network is equipped with a BOOTP/DHCP server (default)
The card is configured by default with this service enabled. No manual configuration is required.The IP parameters are automatically collected by the card.
To view the network configuration(from the main configuration
◗ Press the 2 key (Network configuration), then press the ↵ key. ◗ Press the 1 key(Read Network settings)., then press the ↵ key. The settings supplied by the server are displayed:
Network configuration :
MAC address : 00:06:23:00:1C:07
Mode : DHCP
IP address : 172.17.23.18
Subnet mask : 255.255.248.0
Gateway : 172.17.17
◗Note the IP address.
◗Press the ↵ key
◗Press the 0 key (Exit), then press the ↵ key.
◗Press the 0 key (Exit), then press the ↵ key.
Your network is not equipped with a BOOTP/DHCP server
Manual configuration is required.
To set the network configuration(from the main configuration menu):
◗Press the 2 key (Network configuration), then press the ↵ key.
◗Press the 2 key (Modify Network settings), then press the ↵ key.
◗Follow the instructions and enter the IP parameters:
1 : Read Network settings
2 : Modify Network settings
3 : Set ethernet speed
0 : Exit
For each of the following questions, you can press "Return" to select the value shown in braces, or you can enter a new value
Should this target obtain IP settings from the network?[N] N Static IP address [172.17.16.16]?172.16.1.82
Subnet mask IP address [255.255.0.0]? 255.255.255.0 Gateway address IP address [0.0.0.0]? 172.17.17.1 Done
Wait until "Done" is displayed, indicating that the IP parameters have been saved.
◗Press the 0 key (Exit), then press the ↵ key.
◗Press the 1 key (Reset), then press the ↵ key.
The card restarts with the new IP settings (after approx. two minutes).
ACCESS TO SUPERVISION
To check whether the Network Management Teleservice Card is operational after installation and IP settings, proceed as follows.
◗Run a browser
◗Enter in the address bar:
http://IP address/ (e.g. http://172.16.1.82/)
◗The home page is displayed:
◗Set the time by clicking the Time command.
◗Continue configuration via the sections in the Settings menu.
Teleservice procedure
◗Install the Network Management Teleservice Card kit using the present manual.
◗Fill in the information form (3402228500).
◗Send the form to your Teleservice centre (by Fax or Internet).
◗Your centre will activate this service.
◗You receive an acknowledgement of receipt.
The information form must be sent back in order to trigger remote monitoring of your equipment.
USER MANUAL
The manual (34003991EN) provides all the information required to use, install and configure the Network Management Teleservice Card.
For more information on the supervision, control and configuration functions offered by the Network Management Teleservice Card, see the user manual on the www.apc.com web site.
3402231500/AC
