![](/images/new-backgrounds/1068371/683717x1.webp)
4. OPERATION
Operating Instructions (see figure #4)
This toaster is for Dry operation only (no oil). Do not put buttered bread products in the toaster.
Ensure Release Sheets are properly installed. (See page 7.)
Turn Main Power Switch on. Set Temperature Control to desired temperature. (Temperature is factory set at 600°F.)
Allow Pilot Light to cycle at least two times (on/off). When the light is on, the grill is heating. Heat up time
is about 15 minutes. |
|
| FIGURE 2: | |||
Place bun halves on feeder cut side down (facing grill |
| |||||
BUN THICKNESS DIALS | ||||||
| surface). Toast time is approximately 8, 20 or 30 |
| ||||
|
|
|
|
| ||
| seconds depending on bun height, diameter and model |
|
|
| ||
| purchased. Increase or decrease temperature setting |
|
|
| ||
| and/or Bun Thickness Dials to achieve desired |
|
|
| ||
| brownness and temperature. |
|
|
|
Bun Thickness Adjustment
The VSX is designed to accommodate a variety of different products. Adjust for product thickness by setting the Bun Thickness Dials on the side of the toaster to the appropriate setting. Settings for different thicknesses are indicated on the label adjacent to the Bun Thickness Dials. See figure 2.
| FIGURE: 3 |
| ||
UP: |
| While pressed, displays the |
|
|
| TEMPTEM. PCONTROLILOTALARMUPDOWN |
| ||
|
| least 3 seconds to increase set point. |
|
|
|
|
|
| |
DOWN: | While pressed, displays the |
|
| |
|
| least 3 seconds to decrease set point. |
|
|
TEMP: |
| Press to momentarily display the actual platen temperature. |
|
|
PILOT: |
| Illuminated when power is being applied to heater. |
|
|
POWER: | Main power supply to the toaster. |
|
| |
Operation of Controller (See Figure 3) |
|
| ||
1. Make sure that all the doors are closed and the lid is on. (It should |
|
| ||
| look like the photograph on the cover.) |
|
| |
2. | Make sure toaster is plugged in to the correct voltage. The voltage |
|
| |
| of the toaster is written on the data plate. The data plate is located |
|
| |
| on the back of the toaster near the cord. |
|
| |
3. | Turn the toaster on (POWER). “” is on and “O” is off. |
|
| |
4. | When main power is applied, the digital display will boot up (displays “888” and then the software | |||
| version information). Then it will display “Lo.” (If the toaster is already warm, it might display “Hi.”) | |||
5. | The toaster remembers the last set point that was entered, even if you turn the toaster off. APW | |||
| recommends a set point of 600°F or below. If you wish to change the set point, press (and hold) | |||
| either the UP or DOWN key. Display will change set point by 1 degree for the first 5 degrees, and | |||
| then it will jump by 5's. When you reach the set point that you want, let go of the button. You may | |||
| then press the UP or DOWN key to make further changes. If you don't press any buttons for 5 | |||
| seconds, then the new set point will take effect. |
|
| |
6. | When the set point is changed, the display will say “Lo” or “Hi” until the set point is reached. After | |||
| that time it will say “rdY.” While it says “rdY” the platen will cycle on and off to maintain the set point. | |||
| Whenever heat is applied to the platen, the PILOT LED will be illuminated. | |||
7. | It takes the toaster |
|
|