installation
Positioning the unit
<Place the Logo speaker unit on a level, firm surface, avoiding direct sunlight and sources of heat or damp.
<Do not place Logo in an enclosed space such as a bookcase or closed cabinet unless there is good provision for ventilation.The Logo speaker unit is designed to run warm during normal operation.
<Do not place your record deck on top of Logo. Record decks are very sensitive to the noise generated by mains power supplies which will be heard as a background ‘hum’ if the record deck is too close.Vibrations from Logo may also cause the pickup stylus to jump tracks.
Power
Logo is supplied with a moulded mains plug already fitted to the lead. Check that the plug supplied fits your supply – should you require a new mains lead, please contact your Arcam dealer. Logo is fitted with a transformer designed to accept nominal mains voltages from 100V to 240V.
Push the IEC plug end of the power cable into the socket on the back of Logo, making sure that it is pushed in firmly. Plug the other end of the cable into your mains socket and, if necessary, switch the socket on.
Logo is fitted with a main power switch on the rear panel, above the power inlet: make sure that this is switched on to use Logo.
If your Logo is not to be used for a prolonged period, switch the unit off at the main power switch.
85 | 100 115 |
| 0.9 |
|
| 4 | 5 6 |
|
|
| AUTO MANUAL | ||||||
|
|
|
| 0.7 | 1.1 | 3 |
|
|
| 7 |
|
|
|
|
| ||
70 |
| 125 |
|
|
|
| 2 |
|
|
| 8 |
|
|
|
|
| |
50 |
| 0.5 |
|
| 1.3 | 1 |
|
|
| 9 |
|
|
|
|
| ||
| 140 |
|
|
|
|
|
|
|
|
|
|
|
| ||||
35 | 160 | 0.3 | 1.5 |
| 0 |
| 10 |
| PHASE | STANDBY | |||||||
| VOLUME | ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IN | OUT |
L | L |
ON | OFF |
R | R |
LFE | LFE |
| USE ONLYWITH A 250V FUSE |
| |
| FUSE: T2.5AL 250V |
Indicator LED
An indicator LED is positioned across the top edge of Logo’s cabinet.
When the indicator LED is off, it indicates that the speaker is completely disconnected from the mains. A blue
light from the indicator shows that the speaker is powered up and ready for immediate use. A red light from the indicator shows that the speaker is in standby
Standby switch
AUTO MANUAL | The |
| settings: Auto and Manual. |
STANDBY ‘Auto’ (button out) switches Logo’s amplifier to standby after a period of
idleness (about 15 minutes) when no audio signal has been received.‘Manual’ (button in) means that Logo’s amplifier is on whenever the unit is receiving mains power.
Interconnect cables
We recommend the use of
It is good practice when connecting your equipment to make sure that the mains
Note: When connecting Logo to signal leads, or when moving Logo to a new position, make sure that the unit is not receiving power by switching off and disconnecting the power lead.
Connecting to a sound source
Check that your sound processor/receiver is switched off before connecting Logo. Failure to do this may result in both speaker and amplifier damage.
If your sound source has a
output (Pre out L and Pre out R) to IN L and IN R,
respectively.
You may connect both the LFE and the L and R outputs to Logo if you wish to use both the LFE channel and to supplement the bass response of ‘Large’ Left and Right speakers.
Out L, Out R and OUT LFE provide
After connecting
Turn the sound source amplifier volume down to minimum before switching on. Switch the source amplifier on, select a source signal, then gradually increase the volume to the required listening level.
Care of your speaker
Running-in
In the same way as a new car requires a
Cleaning
To clean your speaker simply use a soft, slightly dampened cloth to wipe off any dust or dirt. Do not use
Power handling
Arcam speakers are designed to reproduce recorded music under normal domestic conditions.We do not recommend nor warrant them for commercial applications, such as discothèques, public address, etc.