Using the remote control
CR-389 Remote Control
The
E n g l i s h
TUNER |
|
|
|
|
|
|
|
|
These buttons are used to control tuner functions. |
|
|
|
|
|
|
|
|
Note that the FM/DAB lights indicate into which mode |
| TUNER |
|
|
|
|
|
|
you are switching the remote control. The lights only |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
illuminate for five seconds to conserve battery power. | FM DAB |
|
|
| Power/Standby |
| ||
|
|
|
|
| ||||
If neither light is illuminated this does not mean that the | DAB | MENU | DISP |
| Toggles the amplifier between standby mode and full power | |||
remote control is not working! |
| mode. The power indicator light next to the power button on | ||||||
| FM |
|
|
|
|
|
|
|
|
|
|
|
| the front panel is red if the amplifier is in standby, amber while | |||
| the amplifier is powering up (this only takes a few seconds) and | |||||||
(UP and DOWN) |
|
|
|
| green when the amplifier is powered up. | |||
|
|
|
| |||||
Perform the same function as the |
|
|
|
| ||||
|
|
|
|
|
|
|
| |
buttons on the front panel (see page 6). | MODE |
|
| BAND | SP1 and SP2 |
|
| |
|
|
|
|
| ||||
|
|
|
|
|
|
| ||
|
|
|
|
| These buttons allow you to select and deselect the main | |||
|
|
| SP1 |
| (SP1) and secondary (SP2) sets of speakers attached to your | |||
|
|
|
| amplifier (see page 6). |
| |||
|
|
|
|
|
| |||
ENTER | ENTER |
| SP2 | DISP |
|
|
|
|
Performs the same function as the ENTER |
|
|
|
|
|
|
|
|
button on the front panel (see page 8). |
|
|
|
| DISP (display) |
|
| |
| SEL |
|
|
|
|
| ||
|
|
|
|
| Cycles through the settings ‘Bright’, ‘Off’ and ‘Dim’. Turning | |||
SELECT |
|
|
|
| the display ‘Off’ generally gives a slight improvement in sound | |||
|
|
|
| quality. |
|
|
| |
Performs same function as the SELECT button on the front |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
panel. It allows you to use the remote’s volume switch in the |
|
|
|
|
|
|
|
|
same way you use the control dial on the front panel – to |
|
|
|
|
|
|
|
|
adjust various amplifier settings (see page 8). |
|
|
|
|
|
|
|
|
Note that pressing + corresponds to turning the |
|
|
|
| Volume and | (mute) |
| |
Control knob clockwise, – to anticlockwise. |
|
|
|
| Press + to increase volume or – to decrease the output volume | |||
| PHONO | AUX | CD | TUNER | of the amplifier. |
|
| |
|
|
|
|
| Press | to mute the speaker connections and preamp outputs. | ||
Source selection buttons | AV | DVD | VCR | TAPE | Both tape outputs and the headphone socket remain active. | |||
|
|
|
| Mute is disabled either by pressing | again, or by adjusting | |||
These operate in the same way as the source selectors |
|
|
|
| ||||
| AMPLIFIER |
| the volume. |
|
| |||
on the front panel of your integrated amplifier. |
|
|
|
| ||||
|
|
|
| You can use the remote’s volume control in conjunction with the | ||||
|
|
|
|
| ||||
|
|
|
| RPT | SELECT button to adjust balance, tone and amplifier settings. | |||
|
|
| PROG | DISP | CD controls |
|
| |
|
|
|
|
|
|
| ||
|
| CD |
|
| These offer basic controls of Arcam CD players | |||
|
|
|
|
|
|
|
| |
NOTE: Remember to install the two supplied AAA batteries |
|
|
|
|
|
|
|
|
before trying to use your remote control! |
|
|
|
|
|
|
|
|
Do not place anything in front of the IR receiver on the left | A85/P85 | |
of the A85, or the remote control may not work. | ||
9 | ||
| ||
|
|
