MARGHERITA
Mounting the Parts onto the Face of the Machine
-Mount the hinge supports onto the face of the machine, positioning the hole indicated by the arrow in fig. 1 towards the inside of the face and using the type C screws.
-Mount the magnetic plate on the opposite side, at the top, using the two type B screws.
-Place the spacer illustrated in fig. 4/B between the appliance front and the magnet receiver.
Using the Drilling Template
-To trace the positions of the holes on the
-To trace the positions of the holes on the
-Useanappropriatelysizedrouter to mill the holes for the two hinges, the rubber plug and the magnet.
Mounding the Parts onto the Wooden Panel (Door)
-Insert the hinges into the holes (the movable part of the hinge must be positioned facing away from the panel) and fasten them with the 4 type A screws.
-Insert the magnet into the top hole on the opposite side of the hinges and fasten it with the two type B screws.
-Insert the rubber plug into the bottom hole.
The panel is now ready to be mounted onto the machine.
Mounting the Panel into the machine
Insert the nib of the hinge (indicated by the arrow in fig. 2) into the hole for the hinge and push the panel towards the front of the machine. Fasten the two hinges with the type D screws.
Fastening the plinth guide
If the machine is installed at the end of a set of modular cabinets, mount either one or both of the guides for the base molding (as shown in fig. 8). Adjust them for depth based on the position of the base molding, and, if necessary, fasten the base to the guides (fig. 9).
This is how to assemble the plinth guide (fig.8):
Fasten angle P using screw R, insert plinth guide Q into the special slot and once it is in the desired position, lock it in place using angle P and screw R.
Inserting the machine into the Cabinet
-Push the machine into the opening, aligning it with the cabinets (fig. 6).
-Regulate the adjustable feet to raise the machine to the appropriateheight.
-To adjust the position of the wooden panel in both the vertical and horizontal directions, use the Cand Dscrews,asshowninfig.7. Important:closethelowerpartof the appliance front by ensuring that the plinth rests against the floor.
| 600 min | ||
540 | 595 |
|
|
|
|
| |
815 |
|
| 900÷820 |
| 570 | m | in |
|
| ||
Fig. 6
C |
D |
C |
Fig. 7 | Fig. 8 | Fig. 9 |
Accessories provided for the height adjustment
Thefollowingcanbefoundinside the polystyrene lid (fig. 10):
2 crossbars (G),
1 strip (M)
Fig. 10
the following can be found inside the appliance drum:
4additional feet (H),
4screws (I),
4screws (R),
4nuts (L),
2 plinth guides (Q)
Adjusting the appliance height
The height of the appliance can be adjusted (from 815 mm to 835 mm), by turning the 4 feet. Should you require the appliance to be placed higher than the above height, you need to use the following accessories to raise it to up to 870 mm:
-the two crossbars (G)
-the 4 feet (H)
-the 4 screws (I)
-the 4 nuts (L)
then perform the following operations (fig. 11):
remove the 4 original feet, place a crossbar G at the front of the appliance, fastening it in place using screws I (screwing them in wheretheoriginalfeetwere)then insert the new feet H.
Repeat the same operation at the back of the appliance.
Now adjust feet H to raise or lower the appliance from 835 mm to 870 mm.
Once you have reached the desired height, lock nuts L onto crossbar G.
G |
| |
L | I | |
H | ||
|
Fig. 11
To adjust the appliance to a height between 870 mm and 900 mm, you need to mount strip M, adjusting feet H to the required height.
Insert the strip as follows: loosen the three screws N situated at the front of the Top cover of the appliance, insert strip M as shown in fig. 12, then fasten screws N.
M |
Fig. 12
Margherita - Iinstructions for installation and use 14
