ASA Electronics DV2007 Installation, Before You Begin, Important Notes, Disc Maintenance

Screw Stud

DV2007

		Table 1: General Disc Information				INSTALLATION
						Before You Begin
Disc Type	Logo			Diameter/	Playback Time
				Playable Sides		1.	Disconnect Battery
							Before you begin, always disconnect the battery negative terminal.
DVD Video				12 cm single/double	133 minutes (4.7 GB)	2.
							Remove Transport Screws
				side	242 minutes (8.5 GB)
						Important Notes
	TM			(1 layer & 2 layer)	266 minutes (9.4 GB)
					484 minutes (17 GB)	•	Before final installation, test the wiring connections to make sure the unit is connected
Audio CD				12 cm single side	74 minutes
							properly and the system works.
			REWRITABLE			•	Use only the parts included with the unit to ensure proper installation. The use of
							unauthorized parts can cause malfunctions.
MP3/MWA Disc	CD-Rs or CD-RWs recorded in MP3, MPEG1 or 2, 2.5 Audio Layer 3 and
						•	Consult with your nearest dealer if installation requires the drilling of holes or other
	WMA Version 7 and 8. The recorded format must be compliant with ISO
							modifications to your vehicle.
	9660 Level 1, ISO 9660 Level 2, Romeo, or Joliet.
						•	Install the unit where it does not interfere with driving and cannot injure passengers if
Disc Maintenance						•	there is a sudden or emergency stop.
Before playing, wipe the disc using a clean cloth, working from the center hole towards the							If the installation angle exceeds 30º from horizontal, the unit might not give optimum
							performance.
outside edge.
						•	Avoid installing the unit where it will be subject to high temperatures from direct sunlight,
Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent.
							hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.
						•	Be sure to remove the control panel before installing the unit.

Insert label	Do not bend.	Never touch	Wipe clean from
side up.		the under side	the center to the
		of the disc.	edge.

NOTE: A disc may become scratched (although not enough to make it unusable)

DIN Front/Rear Mount

This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear” (DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis) mount. For details, refer to installation methods A and B.

DIN Front Mount (Method A)
1.	Remove the detachable front panel, if it is	Dashboard
	attached to the chassis, by pushing the
	REL button.	Bend Tabs
2.	Slide the mounting sleeve off of the	182

chassis if it has not already been removed.

depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player.

If it is locked into position, use the removal keys (supplied) to disengage it. The removal keys are depicted on page 4.

53

3.Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily

slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

4.Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

5.Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

6.Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation.

7.After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (vehicle ignition switch must be on). If the unit does not operate,

3