Asus 810E2 MICROATX MOTHERBOARD .3 SETUP H/W

(This page was intentionally left blank.)

Memory System

.3 SETUP H/W

Contents

Page USER'S NOTICE Product Name: ASUS TUWE-M Manual Revision: 1.01 E919 ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) CONTENTS 3.7.1 Installing an Expansion Card 3.7.2 Assigning IRQs for Expansion Cards 3.7.3 Communication and Networking Riser (CNR) Slot 4.1.1 Upon First Use of the Computer System INDEX FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver 1.1How This Manual Is Organized 1.2 Item Checklist 2.1The ASUS TUWE-M 2.1.1 Core Specifications 2.1.2Connections 2.1.3Special Features 2.1.4Performance and Intelligence 2.2TUWE-MMotherboard Components 2.2.1Component Locations 3.1TUWE-MMotherboard Layout 3.2Layout Contents 3.3Hardware Setup Procedure 3.4Motherboard Settings 3. HARDWARE SETUP Motherboard Feature Settings 1)Onboard PCI Audio Setting (AUDIO_EN) The onboard PCI audio may be enable or disabled using this jumper Motherboard Settings 2)USB Device Wake Up (USBPWR01, USBPWR23) Control NOTES 1.For suspend to RAM function, these jumpers must be set to Enable Setting 3)USB/CNR Selection (CNRUSB1 / CNRUSB2) 4)Keyboard Power Up (KBPWR) Power Up Control 5)CPU External Frequency Setting (DSW) Frequency Selection Table 3.5System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) .3 SETUP H/W 3.7Expansion Cards 3.7.1 Installing an Expansion Card 3.7.2Assigning IRQs for Expansion Cards Standard Interrupt Assignments Interrupt Request Table for this Motherboard 3.8External Connectors 3)Universal Serial BUS Ports 0 & 1 (Black two 4-pinUSB) USB Headers 4)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) Serial Port Connectors (Teal/Turquoise 9-pin COM1 pin COM2) Onboard Serial Port 1/2 9)Fast-EthernetPort Connector (RJ45) (optional) network hub 10)Floppy Disk Drive Connector (34-1pinFLOPPY) DMA Channels 11)Primary (Blue) / Secondary IDE Connectors (Two 40-1pinIDE) IMPORTANT: 12)IDE Activity LED (2-pinIDELED) 13)CPU (CPU_FAN), Chassis (CHA_FAN) Fan Connectors (3 pins) do not place jumper caps over these pins 14)Internal Audio Connectors (4-pinCD1, AUX, MODEM) 15)Infrared Connector (10-1pin IrDA) 16)ASUS Special Audio Connector (12-1pin AUDIO) Extra audio control is supported by an audio panel linked to this connector 17)LCD-TVHeaders (18-pin, 18-1pin LCD TV) These headers require optional modules for LCD or TV output 18)USB Header (10-1pin USB2) 19)ATX Power Supply Connector (20-pinblock ATXPWR) 20)System Power LED Lead (3-1pin PWRLED) 21)Keyboard Lock Switch Lead (2-pinKEYLOCK) 22)System Warning Speaker Connector (4-pinSPEAKER) 23)System Message LED Lead (2-pinMSG.LED) 24)System Management Interrupt Lead (2-pinSMI) 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 4.1.2 Updating BIOS Procedures Page 8.Follow the onscreen instructions to continue 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] A Note about Passwords Forgot the Password Halt On [All Errors] Installed Memory [XXX MB] 4.4Advanced Menu PS/2 Mouse Function Control [Auto] USB Legacy Support [Auto] OS/2 Onboard Memory > 64M [Disabled] 4.4.1Chip Configuration SDRAM Page Closing Policy [One Bank] CPU Latency Timer [Enabled] Onboard VGA [Enabled] Graphics Window Size [64MB] Memory Hole At 15M-16M[Disabled] 4.4.2I/O Device Configuration UART2 Use Standard Infrared [Disabled] Onboard Parallel Port [378H/IRQ7] Parallel Port Mode ECP DMA Select Parallel Port Mode [ECP+EPP] 4.4.3PCI Configuration PCI/PNP IRQ Resource Exclusion 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend-to-RAMCapability [Disabled] APIC Mode [Disabled] 4.5.1Power Up Control Wake On PS2 KB/PS2 Mouse/CIR [Disabled] Wake Up By PS2 Keyboard [Space Bar] Wake On PS2 KB/PS2 Mouse/CIR Wake On USB for S3 or S4 State [Disabled] USB Device Wake Up 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence Plug & Play O/S [No] Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Enabled] Full Screen Logo [Enabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5.1Install Operating System 5.2 Start Windows 5.3TUWE-MMotherboard Support CD 5.3.1 Installation Menu 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe 6. SOFTWARE REFERENCE Settings CPU Cooling System Setup History Information Memory Device Summary DMI Explorer Utility Execute Program 6.1.3ASUS PC Probe Task Bar Icon 6.2ASUS Live Update 6.3CyberLink PowerPlayer SE 6.3.1 Starting CyberLink PowerPlayer SE 6.3.2 CyberLink PowerPlayer Control Panel 6.4CyberLink VideoLive Mail 6.4.1Starting VideoLive Mail 6.4.2CyberLink VideoLive Mail User Interface 6.53Deep Color Tuner 6.5.1 3Deep Color Tuning 6.5.2 The 3Deep Control Panel Page 7.1 Glossary APPENDIX Page Page INDEX