Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus A7V NOTE:, NOTE:, (40-1pin PRIMARY IDE/SECONDARY IDE), (40-1pin PRIMARY ATA100/SECONDARY ATA100), 9)Primary (Blue) / Secondary IDE Connectors

1 112

Download 112 pages, 4.33 Mb

.3

H/WConnectors

SETUP

3.HARDWARE SETUP

9)Primary (Blue) / Secondary IDE Connectors(40-1 pin PRIMARY IDE/SECONDARY IDE)(40-1 pin PRIMARY ATA100/SECONDARY ATA100)

These connectors support the provided IDE hard disk ribbon cables. Connect the cable’s blue connector to the motherboard’s primary (recommended) or sec- ondary IDE connector, and then connect the corresponding gray connector to your UltraDMA/100 / UltraDMA/66 slave device (hard disk drive) and the black connector to your UltraDMA/100 / UltraDMA/66 master device. It is recom- mended that non-UltraDMA/100 / Ultra/66 devices be connected to the second- ary IDE connector.

NOTE: UltraDMA/100 is backward compatible with DMA/66, DMA/33, and DMA and with existing DMA devices and systems so there is no need to upgrade current EIDE/IDE drives and host systems.

If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Refer to your hard disk documentation for the jumper settings. BIOS now supports specific device bootup (see 4.6 Boot Menu).

(Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). If you have more than two UltraDMA/100 / UltraDMA/66 devices, you will need to purchase another UltraDMA/100 / UltraDMA/66 cable.

NOTE: The hole near the blue connector on the UltraDMA/100 / UltraDMA/66 cable is intentional.

TIP: You may configure two hard disks to be both Masters with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through 4.6 Boot Menu.

IMPORTANT: UltraDMA/66 and UltraDMA/100 IDE devices require a 40-pin 80-conductor cable to be enabled.

NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.

A7V

A7V IDE Connectors

Primary Ultra ATA100 IDE Connector	Secondary Ultra ATA100 IDE Connector	Primary IDE Connector	Secondary IDE Connector
	PIN 1		PIN 1

36	ASUS A7V User’s Manual

Contents

JumperFree™ PC133/VC133 200MHz FSB AGP Pro/4X ASUS A7V 1.03 E601 August ASUS A7V User’s Manual ASUSTeK COMPUTER INC. (Asia-Pacific) ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) Page Page Page 1.1How This Manual Is Organized 1.2 Item Checklist 2.1The ASUS A7V 2.1.1 Specifications Wake-On-Ring Connector: USB: PC Health Monitoring: PCI/AMR Expansion Slots: 2.1.2Special Features 2.1.3 Performance Features 2.1.4Intelligence 2.2Motherboard Components 2.2.1Component Locations 3.1Motherboard Layout 3.2Layout Contents SETUP H/W 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Features Settings (DIP Switches - DSW) 1) JumperFree™ Mode (JEN) Setting DSW VID 2)Onboard Audio Setting (AUDIOCODEC) Setting AUDIOCODEC 3)PCI 3Volt Setting (3VSBSLT) 3VSBSLT 4)I/O Voltage Setting (VIO) Setting VIO 5)CPU External Frequency Setting (DSW Switches 1–4) 1) JumperFree™ Mode (JEN) 3. HARDWARE SETUP Operating Frequency Setting 4.4 Advanced Menu 6)CPU Core:BUS Frequency Multiple (DSFID Switches 1–4) CPU Core:Bus Freq. Multiple Manual CPU Settings Set the DIP switches by the internal speed of your processor as follows: 7)Voltage Regulator Output Setting (VID1, VID2, VID3, VID4) 3.5System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) CAUTION H/WSETUP 3.6.1ASUS P2T-Cable 3.7Expansion Cards 3.7.1 Expansion Card Installation Procedure 3.7.2Assigning IRQs for Expansion Cards 3.7.3Accelerated Graphics Port Pro (AGP Pro) 3.7.4Audio Modem Riser (AMR) Slot 3.8External Connectors 4)Serial Port Connectors (Teal/Turquoise 9-pinCOM1 / COM2) Onboard Serial Port 4.4.2 I/O Device Configu- ration 5)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 6)Game/MIDI Connector (Gold 15-pinGAME_AUDIO) (optional) 7)Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) 8)Floppy Disk Drive Connector (34-1pin FLOPPY) 9)Primary (Blue) / Secondary IDE Connectors (40-1pin PRIMARY IDE/SECONDARY IDE) (40-1pin PRIMARY ATA100/SECONDARY ATA100) 10)Chassis Intrusion Lead (2 pin CHASSIS) 11)Standard and Consumer Infrared Module Connector (5-pinIR) UART2 Use Infrared 4.4.2 I/O Device Configuration) 12)Wake-On-LANConnector (3-pinWOL_CON) 4.5.1 Power Up Control 13)Wake-On-RingConnector (2-pinWOR) 6. SOFTWARE REFERENCE not supported do not place jumper caps over these pins 15)Internal Audio Connectors (4-pinCD_IN, AUX, VIDEO, MODEM) 16)Internal Microphone Header (3-pinMIC2) 17)Headphone True-LevelOut Header (3-pinHPHONE) 18)USB Headers (5-1pin USB3A, 10-1pin USBPORT/USB3) (optional) 19)SMBus Connector (5-1pin SMB) 20)ATX Power Supply Connector (20-pinblock ATXPWR) 21)Power Supply Thermal Sensor Connector (2-pinblock JTPWR) 22)IDE Activity LED (2-pinIDELED) will not A7V System Panel Connectors 23)System Warning Speaker Connector (4-pinSPEAKER) 24)System Power LED Lead (3-1pin PWRLED) 25)System Message LED Lead (2-pinMSG.LED) 26)Reset Switch Lead (2-pinRESET) 27)ATX Power Switch Lead (2-pinPWRSW) 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 4.1.2 Updating BIOS Procedures Page Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] A Note about Passwords Forgot the Password Halt On [All Errors] Installed Memory [XXX MB] 4.4Advanced Menu System Performance Setting [Optimal] CPU Vcore Setting [Auto] CPU Vcore CPU Level 1 Cache, CPU Level 2 Cache [Enabled] CPU Level 2 Cache ECC Check [Disabled] Notes for JumperFree Mode 4.4.1Chip Configuration SDRAM Configuration [By SPD] SDRAM CAS Latency SDRAM Configuration SDRAM RAS Precharge Time SDRAM RAS to CAS Delay Memory Early/Delay Write [Auto] Memory Data Drive [Auto] CAS# Drive [Auto] DIMM Interleave Setting [Auto] Graphics Aperture Size [64MB] 4.4.2I/O Device Configuration Onboard Peripheral Resource Control Game Port Function [Disabled] Onboard Legacy Audio Support [Disabled] Sound Blaster Emulation [Disabled] Sound Blaster I/O Base Address [220h-22Fh] Sound Blaster IRQ [IRQ5] 4.4.3PCI Configuration PCI/PNP IRQ Resource Exclusion PCI/PNP DMA Resource Exclusion PCI/PNP UMB Resource Exclusion 4.4.4Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend-to-RAMCapability [Disabled] Suspend Mode [Disabled] 4.5.1Power Up Control Automatic Power Up [Disabled] 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence Other Boot Device Select [INT18 Device (Network)] Plug & Play O/S [No] Reset Configuration Data [No] Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5.1Install Operating System 5.2 Start Windows 5.3A7V Series Motherboard Support CD 5.3.1 Installation Menu 5.4VIA 4 in 1 drivers 5.5Win95-98Promise Ultra 100 IDE Controller 5.6ASUS PC Probe 5.7ASUS Update 5.8PC-Cillin98 5.9ADOBE Acrobat Reader 5.10Cyberlink Video and Audio Applications 5.10.1 System Requirements 5.10.2 Cyberlink Contact Information 5.10.3Installation Procedures 5.11Uninstalling Programs Page 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Settings History Fan Control Information Hard Drives Memory Device Summary DMI Explorer Utility 6.1.3ASUS PC Probe Task Bar Icon 6.2CyberLink PowerPlayer SE 6.2.1 Starting CyberLink PowerPlayer SE 6.2.2 CyberLink PowerPlayer Control Panel 6.3CyberLink PowerDVD 6.3.1 Starting CyberLink PowerDVD 6.3.2 CyberLink PowerDVD User Interface 6.4CyberLink VideoLive Mail 6.4.1Starting VideoLive Mail 6.4.2CyberLink VideoLive Mail User Interface Page 7.1PCI-L101Fast Ethernet Card 7.1.1 Features 7.1.2 Software Driver Support 7.1.3 Question and Answer 7.2 Modem Riser 7.2.1 56K Software Modem 7.2.2 Primary/Seconday MR 7.2.3Hardware Installation Procedure 7.2.4Software Setup in Windows 7.3 Glossary Boot Bus Master IDE Byte (Binary Term) COM Port Concurrent PCI LPT Port (Line Printer Port) MMX OnNow PC100 PCI Bus (Peripheral Component Interconnect Local Bus) ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)