Asus M2N68-AM SE2 manual

M2N68-AM SE2

Motherboard

Contents

Page Page Chapter 1: Product introduction Jumpers Chapter 2: BIOS information Managing and updating your BIOS Page Federal Communications Commission Statement Canadian Department of Communications Statement Electrical safety Operation safety How this guide is organized Conventions used in this guide Where to find more information Typography CPU Chipset System bus Memory Graphics Back panel I/O ports BIOS Accessories Form Factor Support DVD Onboard LED 1.2.1Motherboard layout 1.2.2Layout contents 1.4.1Overview 1.4.2Memory configurations M2N68-AMSE2 Motherboard Qualified Vendors List (QVL) DDR2-667MHzcapability DDR2-800MHzcapability DDR2-1066MHzcapability 1.5.1Installing an expansion card 1.5.2Configuring an expansion card 1.5.3PCI slot 1.5.4PCI Express x1 slot 1.5.5PCI Express x16 slot <Del 2.USB device wake-up (3-pin USBPW5-10) 1.7.1Rear panel ports 1.7.2Internal connectors 2.IDE connector (40-1pin PRI_IDE) 3.Optical drive audio in connector (4-pinCD) 4.USB connectors (10-1pin USB56, USB78, USB910) 5.CPU fan connector (4-pinCPU_FAN) 6.ATX power connectors (24-pinEATXPWR, 4-pinATX12V) 7.Speaker connector (4- pin SPEAKER) 8.System panel connector (10-1pin F_PANEL) •System power LED (2-pinPWRLED) •Hard disk drive activity LED (2-pinHDLED) •Power/Soft-offbutton (2-pinPWRBTN) •Reset button (2-pinRESET) 1.8.1Installing an operating system 1.8.2Support DVD information To run the Support DVD 2.1.1ASUS Update utility Installing ASUS Update: Updating the BIOS: 2.1.2ASUS EZ Flash 2 utility 2.1.3ASUS CrashFree BIOS 3 utility Recovering the BIOS 2.3.1System Time [xx:xx:xx] 2.3.2System Date [Day xx/xx/xxxx] 2.3.3IDE Configuration Onboard IDE Controller [Enabled] Serial ATA Devices [Enabled] nVidia RAID Function [Disabled] 2.3.4Primary IDE Master/Slave 2.3.5SATA 2.3.6System Information AMI BIOS Processor System Memory 2.4.1JumperFree Configuration CPU Overclocking [Auto] PCIE Overclocking [Auto] Processor Frequency Multiplier [Auto] Processor Voltage [Standard] Memory Clock Mode [Auto] DRAM Timing Mode [Auto] Memory Voltage [Auto] 2.4.2CPU Configuration GART Error Reporting [Disabled] Microcode Updation [Enabled] Secure Virtual Machine Mode [Disabled] Cool ‘n’ Quiet [Disabled] 2.4.3Chipset NorthBridge Configuration Memory Configuration ECC Configuration SouthBridge Configuration 2.4.4Onboard Devices Configuration Serial Port1 Address [3F8/IRQ4] 2.4.5PCI PnP Plug and Play O/S [No] 2.4.6USB Configuration 2.5.1Suspend Mode [Auto] 2.5.2ACPI 2.0 Support [Disabled] 2.5.3ACPI APIC Support [Enabled] 2.5.4APM Configuration Restore on AC Power Loss [Power Off] Power On By PCI(-E)Device [Disabled] Power On By Ring [Disabled] 2.6.1Boot Device Priority 1st ~ xxth Boot Device 2.6.2Boot Settings Configuration Quick Boot [Enabled] Full Screen Logo [Enabled] 2.6.3Security Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password 2.7.1ASUS EZ Flash