Asus P2B-F 58

V. SOFTWARE SETUP

(This page was intentionally left blank)

SETUP S/W .V

Contents

58	ASUS P2B-F User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS P2B-F Manual Revision: 1.03 E369 Marketing Technical Support CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS P2B-FMotherboard II.FEATURES Wake-On-LAN Connector: •IrDA: Supports an optional infrared port module for a wireless interface Special Features: Intelligent Features: Auto Fan Off: even in sleep mode and system noise The ASUS P2B-FMotherboard Motherboard Parts II. FEATURES Layout of the ASUS P2B-FMotherboard Motherboard Settings Expansion Slots/Sockets Hardware Monitor Connectors Layout Contents Hardware Setup Steps 1. Motherboard Settings Jumpers 1.Keyboard Power Up (KBWK) 2.AGP Frequency Selection (AGPFS) WARNING Motherboard Settings III.HARDWARE SETUP 3.CPU Bus Frequency Selection (FS0, FS1, FS2, FS3) 4.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External 2.System Memory (DIMM) DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) Universal Retention Mechanism Heatsinks Installing the Processor 1. Unlock the URM’s Folding Support Arms: The folding support arms of the URM are locked when shipped To unlock the support arms, simply flip them up to an upright position 3.Insert the SECC/SECC2/SEPP SECC with Pentium II only: 4.Secure the SECC/SECC2/SEPP ASUS Smart Thermal Solutions Recommended Heatsinks for Slot 1 Processors 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor Accelerated Graphics Port (AGP) 5.External Connectors 3.Parallel Port Connector (25-pinfemale) Chipset Features Setup NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinmale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) 7.Primary / Secondary IDE Connectors (Two 40-1pinIDE) 8.IDE Device Activity LED (2-pinIDELED) 9.Chassis / CPU / Power Supply Fan Connectors (3-pinFAN) NOTES: These are not jumpers, do not place jumper caps over these pins 10.Wake-On-LANConnector (3-pinWOL_CON) 11.IrDA-CompliantInfrared Module Connector (5-pinIR) 12.SB-Link™Connector (6-1pin SBLINK) 13.SMBus Connector (5-1pin SMB) 14. ATX Power Supply Connector (20-pinATXPWR) 15.Chassis Intrusion Alarm Lead (4-1pin CHASSIS) 16.System Power LED Lead (3-1pin KEYLOCK) 17.Keyboard Lock Switch Lead (2-pinKEYLOCK) 19.System Message LED Lead (2-pinLED) 20.System Management Interrupt Lead (2-pinSMI) 21.ATX Power Switch / Soft-OffSwitch (2-pinPWRSW) Power Connection Procedures Flash Memory Writer Utility 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer IV. BIOS Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 2.Copy AFLASH.EXE to the just created boot disk Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File 6. BIOS Setup Load Defaults Details of Standard CMOS Setup: Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Auto NOTE: SETUP Defaults are noted in parenthesis next to each function heading Drive A / Drive B Floppy 3 Mode Support Details of BIOS Features Setup BIOS BIOS Processor Serial Number (Enabled) CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache HDD S.M.A.R.T. capability (Disabled) PS/2 Mouse Function Control (Auto) OS/2 Onboard Memory > 64M (Disabled) PCI/VGA Palette Snoop (Disabled) Video ROM BIOS Shadow (Enabled) Details of Chipset Features Setup Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Disabled) IMPORTANT: Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) Auto USB IRQ (Enabled) Load BIOS Defaults Load Setup Defaults Load Supervisor Password and User Password Forgot the password Passwords IDE HDD Auto Detection Save & Exit Setup Save & Exit Exit Without Saving ASUS Smart Motherboard Support CD Installation Submenu DOS Utility Submenu Page ASUS PC Probe Fan Rotation Status PC Temperature Status PC Voltage Status PC Status Summary PC Probe System Info PC Probe Settings PC Probe Task Bar Icon Intel LANDesk Client Manager Toolbar Descriptions Using the Select Computer Dialog Box To select a computer 1.From the main Client Manager window, click File | Select Computer 2.In the Select Computer dialog box, click the computer you want to view 3.Click the Select button To discover new computers Displaying the Properties of a Client Computer Understanding the Computer Status Icons Unavailable Wakeable Wake Pending Normal Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Utility DMI Using Save MIFD Load MIFD Load BIOS Defaults VII. APPENDIX The ASUS CIDB Chassis Intrusion Sensor Module VII. APPENDIX Using the ASUS CIDB 1.You must have an ASUS motherboard with a chassis connector ASUS CIDB Additional Considerations The ASUS S370 CPU Card Setting up the ASUS S370 370Socket ASUS S370 Jumper Settings not ASUS PCI-L101Fast Ethernet Card Features •Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) •Wake-On-LANRemote Control Function Supported •PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications •Consists of MAC & PHY (10/100Mbps) interfaces Glossary Byte (Binary Term) COM Port CPU (Central Processing Unit) Device Driver DOS (Disk Operating System) MMX (Klamath) CPU as well as other PCI Bus (Peripheral Component Interconnect Local Bus) Peripherals POST (Power On Self Test) UltraDMA/33 USB (Universal Serial Bus)