Asus P2E-M (This page was intentionally left blank.)

(This page was intentionally left blank.)

24	ASUS P2E-M User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS P2E-M Manual Revision: Release Date: ASUSTeK COMPUTER INC Marketing Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist The ASUS P2E-MMotherboard Introduction to ASUS Smart Series motherboards Series Smart II.FEATURES Voltage Monitoring and Alert: Auto Fan Off: even in sleep mode and Parts of the ASUS P2E-MMotherboard ASUS P2E-MMotherboard Layout Jumpers Expansion Slots Hardware Monitor Connectors Motherboard Layout Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.CPU External (BUS) Frequency Selection (FS0, FS1, FS2) 4.CPU to BUS Frequency Ratio (BF0, BF1, BF2, BF3) Set the jumpers by the Internal speed of your processor as follows: 2.System Memory (DIMM) DIMM Memory Installation 3.Central Processing Unit (CPU) Pentium II Processor The Motherboard As Shipped Installing the Pentium II Processor: Mount the Pentium II Retention Mechanism: TIP: Insert the SEC Cartridge: Secure the SEC Cartridge: Attach the Thermal Sensor Connector (optional): AAVID Heatsink Elan Vital Heatsink (This page was intentionally left blank.) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor Accelerated Graphics Port 5.External Connectors 3.Parallel Port Connector (25-pinFemale) NOTE: Serial printers must be connected to the serial port 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) Audio Port Connectors (Three 1/8” Female) Line Out Line In Mic Joystick/Midi Connector 9.Primary / Secondary IDE connectors (Two 40-1pinIDE) 10.IDE activity LED (2-pinIDELED) do not place jumper caps over these pins 12.Wake On LAN Connector (3-pinWOL_CON) 13.IrDA / Fast IR-Compliantinfrared module connector (5-pinIR) Chipset Features Setup 14.ATX Power Supply Connector (20-pinblock ATXPWR) 15.Stereo Audio In Connectors (4-pinAUX,CD1) (with optional onboard audio) 16.Stereo Audio In Connector (4-pinCD2) (with optional onboard audio) (with optional onboard audio) 17.Digital Audio Interface (6-pinSPDIFO) 18.Message LED Lead (LED, 2 pins) 19.SMI Suspend Switch Lead (SMI, 2 pins) 20.ATX Power Switch/Soft Power Switch (PWR, 2 pins) 21.Reset Switch Lead (RESET, 2 pins) 22.System Power LED (KEYLOCK, 3 pins) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer IV. BIOS Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Auto Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled BIOS Features Setup Details of BIOS Features Setup BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) BIOS Update (Enabled) Quick Power On Self Test (Enabled) Security Option (System) Supervisor Password User Password System Setup Chipset Features Setup Details of Chipset Features Setup Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Disable Memory Hole At 15M–16M(Disabled) Parallel Port Mode (ECP+EPP) ECP DMA Select (3) ECP ECP+EPP Parallel Port Mode Power Management Setup Details of Power Management Setup Video Off Method (Blank Screen) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake on LAN (Enable) Automatic Power Up (Disabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) USB IRQ (Enabled) Onboard Audio Chip (Enabled) Play / PCI Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving ASUS Smart Motherboard Support CD Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility ASUS PCI-L101Fast Ethernet Card Features Software Driver Support Question and Answer