Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus P4S800-MX SE 6.CPU fan connector (3-pinCPU_FAN1), 5.Front panel audio connector (10-1pin FP_AUDIO1), Be default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins

1 84

Download 84 pages, 3.64 Mb

5.Front panel audio connector (10-1 pin FP_AUDIO1)

This is an interface for the front panel cable that allows convenient connection and control of audio devices.

Be default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins

LINE OUT_L/BLINE_OUT_L are shorted with jumper caps. Remove the caps only when you are connecting the front panel audio cable.

P4S800-MX SE

AGND +5VA BLINE OUT R

BLINE OUT L

FP_AUDIO1

Line out_L

NC

Line out_R

MICPWR

MIC2

P4S800-MX SE Front panel audio connector

6.CPU fan connector (3-pin CPU_FAN1)

The CPU fan connector support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cable to the fan connector on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors!

P4S800-MX SE

CPU_FAN1

GND +12V Rotation

P4S800-MX SE CPU Fan connector

ASUS P4S800-MX SE motherboard

1-21

Contents

Page E1918 First Edition January 1: Product introduction Chapter 2: BIOS Information Chapter 3: Software support Notices Federal Communications Commission Statement •This device may not cause harmful interference, and •Reorient or relocate the receiving antenna •Increase the separation between the equipment and receiver Electrical safety Operation safety P4S800-MXSE specification summary Conventions used in this guide Page Page Intel® 800MHz FSB CPU support SiS661FX/964 chipset DDR400 support Real256E integrated graphics Integrated 10/100 Mbps LAN controller 6-ChannelAudio solution Serial ATA technology USB 2.0 technology ASUS CrashFree BIOS ASUS EZ Flash BIOS ASUS MyLogo2™ C.P.R. (CPU Parameter Recall) Onboard LED 1.5.1 Motherboard layout 1.5.2 Placement direction 1.5.3 Screw holes 1.6.1 Overview Notes on Intel® Hyper-ThreadingTechnology 1.6.2 Installing the CPU 1.7.1 DIMM sockets location 1.7.2 Memory configurations Table 1.7.3 Installing a DIMM 1.8.1 Installing an expansion card 1.8.2 Configuring an expansion card Standard interrupt assignments IRQ assignments for this motherboard 1.8.3 PCI slots 1.8.4 AGP slot 1.9Jumpers 1.Clear RTC RAM (CLRTC1) To erase the RTC RAM: 1.Turn OFF the computer and unplug the power cord 3.Plug the power cord and turn ON the computer 2.USB device wake-up (3-pinUSBPW12, USBPW34, USBPW56, USBPW78) 3.Keyboard power (3-pinKBPWR1) 1.10.1 Rear panel connectors 1.10.2 Internal connectors 3.Serial ATA connectors (7-pinSATA1, SATA2) 4.ATX power connectors (20-pinATXPWR, 4-pinATX12V) 5.Front panel audio connector (10-1pin FP_AUDIO1) Be default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins 6.CPU fan connector (3-pinCPU_FAN1) 7.USB headers (10-1pin USB56, USB78) 8.Digital audio connector (4-1pin SPDIF) 9.Internal audio connectors (4-pinAUX, CD) 10.GAME/MIDI connector (16-1pin GAME1) 11.System panel connector (20-pinPANEL) This connector accommodates several system front panel functions •System power LED (Green 3-pinPLED) •Hard disk drive activity LED (Red 2-pinIDE_LED) •System warning speaker (Orange 4-pinSPEAKER) Page 2.1Managing and updating your BIOS 2.1.1Creating a bootable floppy disk 2.1.2Using AFUDOS to copy the current BIOS 2.1.3Using AFUDOS to update the BIOS 2.1.4Using ASUS EZ Flash to update the BIOS 2.1.5ASUS CrashFree BIOS 2 utility Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1.Remove any floppy disk from the floppy disk drive, then turn on the system 2.Insert the support CD to the optical drive 2.1.6ASUS Update utility Updating the BIOS through the Internet To update the BIOS through the Internet: Launch the ASUS Update utility from the Windows Programs ASUS 5.Follow the screen instructions to complete the update process Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: option from the drop-down 2.2BIOS Setup program 2.2.1BIOS menu screen 2.2.2Menu bar 2.2.3Navigation keys 2.2.4Menu items 2.2.5Sub-menuitems 2.2.6Configuration fields 2.2.7Pop-upwindow 2.2.8Scroll bar 2.3Main menu 2.3.1System Time [xx:xx:xxxx] 2.3.2System Date [Day xx/xx/xxxx] 2.3.3Legacy Diskette A [1.44M, 3.5 in.] 2.3.4Primary and Secondary IDE Master/Slave Type [Auto] LBA/Large Mode [Auto] Block (Multi-sectorTransfer) [Auto] PIO Mode [Auto] 2.3.5OnChip SATA Controller [Raid Mode] 2.3.6System Information 2.4Advanced menu 2.4.1JumperFree Configuration CPU Frequency (Value auto-detected) FSB/CPU External Frequency Synchronization Front Side Bus CPU External Frequency 200 MHz 2.4.2CPU Configuration 2.4.3Chipset Primary Graphics Adapter [PCI] MA 1T/2T Select [Auto] DRAM CAS# Latency [By SPD] DRAM Precharge Delay [Auto] DRAM RAS# Precharge [Auto] Graphics Win Size [64MB] AGP Fast Write Control [Disabled] Share Memory Size [32MB] Onboard AC97 Audio Device [Enabled] 2.4.4Onboard Devices Configuration EPP Version [1.9] 2.4.5PCI PnP 2.4.6USB Configuration 2.5Power menu 2.5.1Suspend Mode [Auto] 2.5.2ACPI 2.0 Support [No] 2.5.3ACPI APIC Support [Enabled] 2.5.4APM Configuration 2.5.5Hardware Monitor 2.6Boot menu 2.6.1Boot Device Priority 2.6.2Removable Drives 2.6.3Boot Settings Configuration Quick Boot [Enabled] Full Screen Logo [Enabled] Add On ROM Display Mode [Force BIOS] Bootup Num-Lock[On] 2.6.4Security Change User Password To set a User Password: 1.Select the Change User Password item and press <Enter The User Password item now shows Installed Clear User Password 2.7Exit menu Page 3.2.1 Running the support CD 3.2.2 Drivers menu SiS AGP driver Onboard graphics driver Realtek ALC655 Audio Driver SIS RAID Controller Driver 3.2.4 ASUS contact information 3.3.1 Installing hard disks Installing Serial ATA (SATA) hard disks 3.3.2 SIS RAID configurations Entering the SIS RAID BIOS utility Create an Array Creating JBOD <1 <Enter <2 up/down <Q <Y Creating RAID 0 for performance 1. From the RAID Setup, press <2> then <Enter> to select RAID 0 (Striping) <N Page Creating RAID 1 for capacity <3 Page Page 3.4Creating a RAID driver disk To use the support CD: 1.Boot your computer and insert the support CD into the optical drive 4.Press <1> to create a RAID driver disk 5.Insert a formatted floppy disk into the floppy drive then press <Enter