Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus PC133, VC133 NOTE:, 10)Floppy Disk Drive Connector (34-1pin FLOPPY), 9)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2)

1 84

Download 84 pages, 2.47 Mb

3.HARDWARE SETUP

9)Primary (Blue) / Secondary IDE Connectors (40-1 pin IDE1/IDE2)

These connectors support the provided UltraDMA/100 IDE hard disk ribbon cable. Connect the cable’s blue connector to the motherboard’s primary (rec- ommended) or secondary IDE connector, and then connect the gray connector to your UltraDMA/100 slave device (hard disk drive) and the black connector to your UltraDMA/100 master device. It is recommended that non-UltraDMA/100 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Refer to your hard disk documentation for the jumper settings. BIOS now supports specific device bootup (see 4.4.1 Advanced CMOS Setup). (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). If you have more than two UltraDMA/100 devices, you will need to purchase another UltraDMA/100 cable.

NOTE: The hole near the blue connector on the UltraDMA/100 cable is intentional.

TIP: You may configure two hard disks to be both Masters with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through 4.4.1 Advanced CMOS Setup.

.3

H/WConnectors

SETUP

A7V-E

A7V-E IDE Connectors

Secondary IDE Connector	Primary IDE Connector
	PIN 1

NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.

10)Floppy Disk Drive Connector (34-1 pin FLOPPY)

This connector supports the provided floppy drive ribbon cable. After connect- ing the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta- tion when using ribbon cables with pin 5 plugged).

FLOPPY

NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.

PIN 1

A7V-E

A7V-E Floppy Disk Drive Connector

30	ASUS A7V-E User’s Manual

Contents

JumperFree™ PC133/VC133 200MHz FSB AGP ASUS A7V-E 1.01 E746 March ASUS A7V-EUser’s Manual ASUSTeK COMPUTER INC. (Asia-Pacific) ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) Page Page Page 1.1How This Manual Is Organized 1.2 Item Checklist 2.1The ASUS A7V-E 2.1.1 Specifications Wake-On-Ring Connector: USB: PCI Expansion Slots: Super 2.1.2Special Features 2.1.3 Optional Components 2.1.4 Performance Features 2.1.5 Intelligence 2.2Motherboard Components 2.2.1Component Locations 3.1Motherboard Layout 3.2Layout Contents 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Features Settings (DIP Switches - SW1) 1) Jumper Setting (JEN) 4.4 Advanced Menu Setting JEN 2)CPU External Frequency Setting (SW1 Switches 1–5) External Frequency Table Frequency Selection Switches ASUS CON TACT INFORMATION) 3)CPU Core BUS Frequency Multiple (DSFID Switches 1–5) Notes 3.5 System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2 Memory Installation Page 3.6Central Processing Unit (CPU) 3.7Expansion Cards 3.7.1 Expansion Card Installation Procedure 3.7.2Assigning IRQs for Expansion Cards 3.7.3Accelerated Graphics Port (AGP) 3.8External Connectors 3)Universal Serial BUS Ports 0 & 1 (Black two 4-pinUSB) USB Headers 4)Serial Port Connectors (Teal/Turquoise 9-pinCOM1 / COM2) Onboard Serial Port 4.4.2 I/O Device Configu- ration 6)Game/MIDI Connector (Gold 15-pinGAME_AUDIO) (optional) 7)Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) 8)Fast-EthernetPort Connector (RJ45) (optional) 9)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2) 10)Floppy Disk Drive Connector (34-1pin FLOPPY) 11)Chassis Intrusion Lead (2 pin CHASSIS) 12)Standard and Consumer Infrared Module Connector (5-pinIR) UART2 Use Infrared 4.4.2 I/O Device Configuration) 13)Wake-On-LANConnector (3-pinWOL_CON) 4.4.3 Power Management 14)Wake-On-RingConnector (2-pinWOR) 6. SOFTWARE REFERENCE do not place jumper caps over these pins 16)Internal Audio Connectors (4-pinCD_IN, AUX, MODEM) 17)Headphone True-LevelOut Header (3-pinHPHONE) 18)USB Header (10-1pin USB2) 19)SMBus Connector (5-1pin SMB) 20)ATX Power Supply Connector (20-pinblock ATXPWR) 21)IDE Activity LED (2-pinIDELED) A7V-ESystem Panel Connectors 22)System Warning Speaker Connector (4-pinSPEAKER) 23)System Power LED Lead (3-1pin PWRLED) 24)Reset Switch Lead (2-pinRESET) 25)ATX Power Switch Lead (2-pinPWRSW) Page 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 4.1.2 Updating BIOS Procedures Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] A Note about Passwords Forgot the Password Halt On [All Errors] Installed Memory [XXX MB] 4.4Advanced Menu CPU Level 1 Cache, CPU Level 2 Cache [Enabled] CPU Level 2 Cache ECC Check [Disabled] BIOS Update [Enabled] PS/2 Mouse Function Control [Auto] USB Legacy Support [Auto] Notes for JumperFree Mode 4.4.1Chip Configuration SDRAM Configuration [By SPD] SDRAM CAS Latency SDRAM Configuration SDRAM RAS Precharge Time SDRAM RAS to CAS Delay Memory Early/Delay Write [Auto] Memory Data Driving [Auto] Memory Address Driving [Auto] DIMM Interleave Setting [Auto] I/O Recovery Time [Disabled] 4.4.2I/O Device Configuration Onboard Peripheral Resource Control Onboard Legacy Audio Support [Disabled] Sound Blaster Emulation [Disabled] Sound Blaster I/O Base Address [220h-22Fh] Sound Blaster IRQ [IRQ5] Sound Blaster DMA [DMA 1] 4.4.3PCI Configuration PCI/PNP IRQ Resource Exclusion PCI/PNP DMA Resource Exclusion PCI/PNP UMB Resource Exclusion 4.4.4Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] CPU Fan in Standby Mode [ON] Suspend Mode [Disabled] 4.5.1Power Up Control 4.5.2 Hardware Monitor 4.6Boot Menu Boot Sequence Other Boot Device Select [INT18 Device (Network)] Plug & Play O/S [No] Reset Configuration Data [No] Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5.1Install Operating System 5.2 Start Windows 5.3A7V-ESeries Motherboard Support CD 5.3.1 Installation Menu ASUS BIOS Flash Utility for LDCM 6.1: Show Motherboard Information: Browse Support CD: ReadMe: Exit: Page 7.1PCI-L101Fast Ethernet Card 7.1.1 Features 7.1.2 Software Driver Support 7.1.3 Question and Answer 7.3 Glossary Boot Bus Master IDE Byte (Binary Term) COM Port Concurrent PCI LPT Port (Line Printer Port) MMX OnNow PC100 PCI Bus (Peripheral Component Interconnect Local Bus) ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)