Athena Technologies AS-1C6, AS-IC6st, AS-IW8, AS-IC8 specification

o w n e r s

m a n u a l

Notes

IMPORTANT SAFETY

INSTRUCTIONS -

READ CAREFULLY !

Read Instructions: All safety and operating instructions should be read before the product is operated.

Retain instructions: Safety and operating instructions should be retained for future reference.

Heed Warnings: All warnings on the product & operation instructions should be adhered to.

Follow Instructions: All operating and use instructions should be followed.

Cleaning: Unplug the product from the wall before cleaning. Do not use aerosol or liquid cleaners, just a damp cloth.

Damage Requiring Service: The product should be serviced by qualified personnel when:

A.The appliance does not appear to operate normally or exhibits a marked change in performance; or

B.Product has been dropped, or damaged.

C.If the product does not operate normally by following the operating instructions.

INTRODUCTION

Congratulations on your purchase of athena TECHNOLOGIES® products! Proprietary technology and high quality manufacturing will allow you to enjoy the most natural and accurate music reproduction for many years. The advice offered in this manual is aimed at helping you maximize and maintain peak performance, and therefore, your listening satisfaction. Please take the time to read all of the instructions contained in this manual to make certain your system is properly installed and functioning correctly.

2)Once you have determined the final mounting position, use the supplied template and mark the cut-out on the wall or ceiling, depending on the model purchased. To mark the cut-out size, simply trace an outline of the supplied template, found in the box, with a pencil.

3)Using the appropriate wall cutting tool, accurately cut the hole in the wall material, based on the appropriate cut-out dimension.

4)Install speaker cable(s) from the receiver or amplifier to the inside of the wall or ceiling, and leave enough slack in the wire so it can hang out from the hole. Using the appropriate wire is essential, as your local municipality may have certain wiring codes that must be maintained.

NOTE: To connect the AS-IC6st you will need to run both the left and right speaker cables to one single hole as this speaker has stereo input connectors.

5)Connect the speaker wire from the positive (RED +) terminal on the receiver to the positive (RED+) terminal on the speaker. Connect the negative (BLACK-) terminal on the receiver to the negative (BLACK-) terminal on the speaker. To connect the wire to the speaker, completely push the appropriate terminal in, and insert the wire through the hole that appears on the terminal. Release the terminal and the internal springs will hold the wire in place. Repeat for the other terminal.

NOTE: If you inadvertently reverse one of the connections (i.e, red to black), you will notice a severe lack of bass from your system. This is called wiring the system “Out of Phase”. If this occurs, check the wiring and re-connect as necessary.

NOTE: To connect the AS-IC6st you must repeat the connection procedure for both left and right channels on one AS-IC6st speaker. This speaker has dual input terminals providing sound for both the left and right channels of your amplifier or receiver.

In Ceiling Models: (AS-IC6, AS-IC8, AS-IC6st)

BREAK-IN PERIOD

We strongly advise that you resist the temptation to play your athena TECHNOLOGIES® speakers to their full capabilities until they have been properly broken in. This process should last approximately 50 to 100 hours of music playback. This can be easily be done by putting your compact disc player on Repeat mode, while playing a CD with a wide dynamic range at average room volume listening levels.

AMPLIFIER REQUIREMENTS

All Energy speakers are designed to be extremely efficient. All models are designed to be 8 ohm compatible allowing playback on almost any amplifier or receiver on the market. Most amplifiers with a power rating of 20-100 watts per channel will effectively operate your athena TECHNOLOGIES® speakers.

Warning: If an amplifier or receiver is over-driven, the resulting distortion is actually many times greater than its rated power. Over-driven amplifier distortion is called “Clipping”, easily identified by its fuzzy, distorted sound, and can damage any speaker. The volume control of most amplifiers and receivers is a logarithmic type, which means that full power may be reached with the volume control set at as little as the halfway point. Operating the loudness, treble, or bass controls increases power output well beyond rated levels. The warranty on your speakers is therefore void if the voice coils are burned or damaged as a result of overpowering or clipping.

LIMITED WARRANTY POLICY

WARRANTY FOR UNITED STATES AND CANADA (see back cover)

Warranty Outside of The United States and Canada:

Product warranties may be legislated differently from one country to another. Ask your local dealer for details of the LIMITED WARRANTY applicable in your country.

NOTE: Please retain the carton and packing material for your athena TECHNOLOGIES® products to protect them in the event of a move or if they need to be shipped to a service center. Product received damaged by a service center that has been shipped by the end user in other than the original packaging will be repaired, refurbished and properly packaged for return shipment at the end user's expense.

INSTALLATION INSTRUCTIONS

NOTE: If you are unable to install the speakers yourself , please contact an authorized installation contractor, or your authorized athena TECHNOLOGIES® retailer.

Caution: Turn off all power in your audio/video system before proceeding with your installation. Not doing so could result in potential damage to the system.

6)Insert the entire speaker into the hole, and using a Philips screwdriver, tighten the screws attached to the dog clamps until firm. DO NOT OVERTIGHTEN

In Wall Models: (AS-IW6)

7)NOTE: Before installing the AS-IW6, set the two position switch on the rear of the speaker to either the 0 dB or the +3db position. The zero position maintains a flat, even frequency response, while the +3db position will increase the sound output to the tweeter. The +3dB position is to be used in rooms with excessive sound absorption material such as thick carpet, drapes, couches, etc.

8)The AS-IW6 speaker installs in two stages. First remove the speaker from the bezel, by removing the 6 screws found on the front of the speaker. Once the screws are removed, separate the bezel from the baffle.

9)Insert the speaker bezel into the hole, and using a Philips screwdriver, tighten the screws attached to the dog clamps until firm. DO NOT OVERTIGHTEN

10)Once the bezel is installed, install the speaker into the mounting bezel and using a Philips screwdriver, tighten the screws until firm. DO NOT OVERTIGHTEN

PAINTING THE BEZEL AND GRILLE

If you wish, you can paint the speaker bezel and grille to match the décor and design of your home.

1)For the in wall model, simply separate the bezel from the speaker baffle and paint the bezel, before you install the speaker portion. The grille is easily separated and can be painted on its own.

2)For the in ceiling models, use the wall template as a paint mask. Carefully cut the marked line on the template to create a template that fits inside the bezel, designed to help facilitate painting. Insert the paint mask, paint the bezel, and then remove the mask when the paint is dry.

NOTE: If you paint the speaker grilles, ensure that the holes are still open allowing sound to come through. If any holes become filled with paint, find a small sharp tool and carefully remove the paint before completing the installation.

FINE TUNING THE SPEAKERS

To fine tune the speakers, you can adjust the angle of the tweeter slightly to direct the sound towards the seating positions. This option is offered in order to compensate for poor mounting locations.

Caution: Be extremely careful when adjusting the tweeter as it is very easy to touch the tweeter, and cause permanent damage which is not covered under the manufacturers warranty. Do not touch the tweeter in any way.

We sincerely hope you enjoy your new speakers for a lifetime!

To install the speakers follow these easy steps:

1)Decide the placement for your speakers. Advanced planning in regards to the placement of your speakers is critical. It is imperative that the wall or ceiling cavity be free from debris, moisture, wall insulation, and any material that is easily combustible. The mounting location must also be void of wall studs or bracing, in the location for the cut- out. Adequate depth for the speaker to fit flush to the wall or ceiling surface is important. If you are unsure about the contents of the wall in which you wish to mount the speakers, simply drill a small hole and using a metal clothing hanger, insert the end of the hanger into the wall and twist it to feel for any debris or wall studs.

AS-IC6st, AS-IC8, AS-IW8, AS-1C6 specifications

Athena Technologies has made significant strides in the field of advanced military and aerospace equipment, particularly with its line of products such as the AS-1C6, AS-IW8, AS-IC8, and AS-IC6st. Each of these models showcases cutting-edge technology designed to enhance operational efficiency and mission success.

The AS-1C6 is renowned for its modular design and versatility. It is engineered to be utilized in various scenarios, providing robust performance in both air and ground operations. This system offers high-resolution sensors that enable real-time data collection and analysis, making it a valuable tool for intelligence, surveillance, and reconnaissance missions. Its capacity for rapid deployment ensures that teams can be operational with minimal downtime.

Next, the AS-IW8 is particularly focused on interoperability. It’s built to seamlessly integrate with other systems, allowing for enhanced communication and coordination across multiple platforms. This feature is critical in joint operations, where collaboration between various military branches and allied forces is essential. The AS-IW8 comes equipped with advanced encryption technologies that ensure secure transmission of sensitive information, safeguarding operational integrity.

The AS-IC8 stands out with its emphasis on electronic warfare capabilities. It incorporates state-of-the-art jamming and countermeasure systems designed to disrupt enemy radar and communication, providing a tactical advantage in hostile environments. Its compact design allows for easy integration onto various platforms without compromising performance. Additionally, the AS-IC8 is optimized for quick adaptability, enabling operators to modify systems in response to evolving threats.

Meanwhile, the AS-IC6st is a specialized variant that caters to specific operational requirements, particularly in support of ground troops. It features enhanced ruggedness and reliability, ensuring that it can withstand harsh environmental conditions and demanding field situations. The AS-IC6st incorporates advanced navigation systems and battlefield management tools that allow troops to maintain situational awareness and coordinate effectively in real time.

Overall, the Athena Technologies AS-1C6, AS-IW8, AS-IC8, and AS-IC6st represent a significant advancement in military technology. Their unique features, robust capabilities, and innovative designs make them indispensable assets for modern armed forces, enabling them to maintain operational superiority in any scenario. As military needs continue to evolve, Athena Technologies remains committed to pushing the boundaries of technology to meet and exceed those challenges.

Athena Technologies AS-1C6, AS-IC6st, AS-IW8, AS-IC8 Important Safety Instructions Read Carefully

Models: AS-IC6st AS-IC8 AS-IW8 AS-1C6