
AIR5
Tabletop IR
Receiver w/Plug
Introduction
The ATON AIR5 is a miniature
Features (Refer to Figure 1)
•3.5mm Quad Plug Accommodates STATUS, IR, +12VDC, & GND
•
•IR Lens Rejects Visible Light Interference
•Internal Crosshatch Shield Inhibits EMI/ESI Interference
•STATUS Indicator: Green LED for System On/Off Indication
•ACTIVITY Indicator: Blue LED Indicates IR Signal Activity
IR Pickup | IR Lens | Status LED | Activity LED |
Diode |
| (Green) | (Blue) |
|
|
| |
|
|
| |
|
|
|
|
| NOTE: Refer to the ATON AIB4 Instructions for power supply considerations and | ||
A: Basic System |
| other important information. |
|
|
Figure 2 shows a basic IR distribution system using the ATON AIB4 Amplified IR |
|
|
|
|
Connection Block, AIR5 IR Receiver, and AIE2 |
|
|
|
|
source equipment. |
| ROOM 1 | ROOM 2 | ROOM 3 |
| AIR1 | |||
|
| AIR6 | AIR1 | |
|
| |||
|
| IR Receiver | ||
|
| IR Receiver | ||
|
|
|
|
A/V Receiver |
| Striped |
Striped | Side | |
| Side |
|
Remote Control |
| IR OUT | GND |
GND |
| +12V | |
IR OUT | STATUS | ||
| +12V |
| |
STATUS |
|
|
AIR5 | Connection Block |
Shelf Top | AIE2 | Rear View |
|
|
IR Receiver |
|
| ||
| Add Resistor at each IR receiver |
|
| |
| Satellite | Wh/Blue IR |
| |
| to reduce STATUS brightness, |
| ||
| Blue STATUS | To Switched | ||
|
| if desired. See text. | Brown GROUND | |
|
| Wh/Green +12 VDC | AC Outlet | |
|
|
|
|
|
| Connection Terminals |
| |
| AIE2 | A/V Receiver |
| |
|
|
| ||
| DVD |
|
| |
| AIR5 |
| PS2 | |
PS2 | Tabletop | AIE1 Emitter | ||
IR Receiver | STATUS | |||
| ||||
Power |
| Satellite | Supply | |
Supply | AIE2 |
|
| |
| AIB4 |
|
|
| To 120V AC | Amplified IR | Figure 2 |
|
| AIE2 |
| (unswitched) | Connection Block |
|
| ||
|
|
|
| DVD | ||
|
|
|
|
|
| |
1. | Place the AIR5 on a shelf top, a cabinet or other horizontal surface. | Figure 2 | PS2 | AIB4 |
| |
or PS3 |
| |||||
2. | Plug the AIR5 and IR emitters into the ATON AIB4, as shown. | Power | Amplified IR | AIE2 | ||
| Supply | Connection Block |
| |||
3. | Set the DIP switches on the AIB4 to LP ON and NET ON or OFF. |
|
|
| ||
|
| To 120V AC |
| |||
4. | Plug in the power supply. |
|
| (unswitched) |
| |
|
|
|
| |||
5. | IR signals sent to the AIR5 will pass through the AIB4 and control the |
|
| Figure 3 | ||
| equipment. |
|
|
|
|
|
Limited Warranty
ATON* warrants to the purchaser/end user (“you”) that the AIR5 is to be free from defects in materials and workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is transferable to subsequent owners of the product as long as the original proof of purchase is retained. If you discover a defect in material or workmanship within the Warranty Period, you can obtain warranty ser- vice by contacting ATON during the Warranty Period at
This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was improperly installed, (c) which was repaired or altered by persons other than ATON or its authorized repre- sentatives or subject to unauthorized tampering, alteration or modification, (d) damaged due to misuse, negligence, accident, acts of God (including, but not limited to, excess moisture, insects, lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events beyond ATON’s control), or (e) subject to improper operation, maintenance or storage or unreasonable use. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. The foregoing remedies shall be your exclusive remedies for any breach of warranty.
Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third Party Products”). With respect to any Third Party Products, the warranty for such product shall be as pro- vided by the manufacturer of such product, who will also be responsible for warranty service, and ATON will pass through to you any transferable warranty actually extended to ATON by the manufacturer.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON- INFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the
ATTENTION: TO OUR VALUED CONSUMERS
Valid proof of purchase is required for all warranty services. Warranty service requests made without proof of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to request warranty service.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
* ATON is a division of ELAN Home Systems, LLC.
|
|
|
| 8' Lead |
|
+12VDC | GND | Red | +12V |
| |
3.5mm Plug | STATUS | IR OUT | Black | GND |
|
|
|
| Yellow | STATUS | Figure 1 |
|
| Internal Wire Colors | White | IR OUT | |
|
|
|
|
Specifications:
•Requires 12VDC power supply, termination block and IR emitters for IR operation.
•Mounting: Sits on any flat surface. A special pad protects the surface on which the AIR5 is placed in addition to providing
•Power: 12VDC @ 6 mA
•Carrier Frequency Acceptance Range: 28kHz to 90kHz.
•Control Range: Up to 35 feet, depending on remote strength and ambient noise conditions
•Control Angle: +/- 50 degrees
•
•Maximum recommended cable length: 1200 feet using
•Dimensions: 3 3/16" (81mm) W x 1 1/8" (28mm) H x 1 1/16" (27mm) D
B:
Figure 3 shows an example of multiple ATON IR Receivers in a multi-room system.
1.Pull Cat-5 from each room (home runs) to the AIB4 terminator near the controlled components.
NOTE: MAX DISTANCE of ALL Wire Runs is 1200 ft using
2.Connect IR receivers in each room to the Cat-5 runs as shown, using the terminal strips supplied.
3.Connect the Cat-5 wires to the correct location on the AIB4 connection terminals (+12VDC, IR, STATUS, and GND).
4.Plug the AIE1 and AIE2 Emitters into the AIB4.
5.Set the DIP switches to LP ON and NET ON.
6.Plug the local AIR5 IR Receiver into the IR RECEIVER jack.
7.Plug in the PS2 12VDC Power Supply.
8.IR signals sent to the IR receivers will pass through the AIB4 and control the equipment.
STATUS Brightness
Figure 3 also shows how an external resistor can be added to reduce the bright- ness of the Status LEDs on ATON IR receivers. In this example, a PS2 12VDC Power Supply is used as the voltage source to indicate ON/OFF status of an A/V Receiver. Choose a resistor value that achieves the brightness you desire (about 2.2k to 12k, 1/8W). Connect it in series with the STATUS lead on each IR receiver, as shown.
www.atonhome.com or service@atonhome.com
©2007 • All rights reserved. | P/N 227943 REV:B |
1 | 2 | 3 | 4 |