![](/images/new-backgrounds/1228814/2288141x1.webp)
Potable Water Pump
6126
Mounting Instructions
SAVE THESE INSTRUCTIONS |
|
Form Number 69239 Rev. B |
FEATURES:
The Potable Water Pump is a rugged, small sized fresh water pump used to deliver water to a faucet. Ideal for use with the Attwood 6142 Faucet/Hand Pump. It is made of ABS
Attwood marine hardware, navigation lighting, interior lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s
CAUTION:
The Potable Water Pump is designed to pump fresh, potable water only. It must not be used to pump gasoline or other flammable liquids.
TOOLS AND MATERIALS REQUIRED:
1.Drill and suitable drill bits.
2.Screwdriver.
3.Wire strippers.
4.Four (4) wire connectors or equivalent.
5.One (1)
6.Two (2) #10 panhead screws (length must not protrude through deck).
7.Suitable length of 3/8" I.D. hose for pump to tank and pump to faucet.
8.Four (4) stainless steel
9.Additional wire, if needed, in 16 or 18 gauge size.
INSTALLATION INSTRUCTIONS:
1.Select a suitable location for this pump, keeping in mind that it must be a dry area.
The pump has intake and outlet fittings to fit 3/8" I.D. soft plastic tubing or 1/4" female pipe thread (cut off hose barb if necessary). Teflon® plumbers tape must be used for all threaded connections and hose clamps for all tubing con- nections.
NOTE: This product is designed to be used with the Attwood 6142
2.After installing the pump, connect the pump’s black lead wire directly to the 12 volt battery negative
An optional power ON/OFF switch, such as Attwood 7589 or 7563, may be installed as a master switch as shown in Figure 2.
The pump may be threaded directly into the tank. However, this is a centrifugal pump and must be positioned lower than the source of water to operate. Do not install on a surface higher than the bottom of your fresh water supply tank.
NOTE: When installing, outlet nozzle should always be higher than inlet nozzle. (See Figure 3)
WIRE CONNECTORS |
|
BLACK | Attwood 6142 |
BROWN | |
|
CITY WATER
CONNECTION
FUSE AND | ||
HOLDER | ||
PRESSURE | ||
| ||
LIMITING |
| |
VALVE |
| |
| CHECK TEE | |
| VALVE | |
| WIRE | |
| CONNECTORS | |
| BLACK |
BROWN
WATER SUPPLY TANK
12VOLT BATTERY
Attwood 6126
POTABLE WATER PUMP
FIGURE 1
OPTIONAL
MASTER SWITCH
INSTALLATION
BROWN | BLACK | |
| ||
|
| Attwood |
|
| 7589 or 7563 |
| BROWN | SWITCH |
TO | TO POTABLE | |
BATTERY |
| WATER PUMP |
FIGURE 2
OUTLET ABOVE INLET
INLET
INLET
OUTLET BELOW INLET
INCORRECTCORRECT
FIGURE 3
CAUTION:
This product is not water resistant and must be installed in a dry location.
Do not use synthetic rubber sealant (Silicone, RTV, etc.) or any sealant which smells like vinegar to seal the pump or its fittings. Use of these materials may cause the pump to crack. It is best to use plumbers Teflon® tape where required.
CAUTION:
ALWAYS protect the pump and the wiring with a 2 amp fuse. For 12 volt DC use only.
ATTWOOD LIMITED WARRANTY
BILGE PUMPS
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331, (“Attwood”) warrants to the original consumer purchaser that this Attwood Potable Water Pump will be free from defects in materials and workmanship under normal use and service for a period of one (1) year from the date of original consumer purchase. This warranty does not extend to any batteries or fuses used with the pump. This limited warranty is not applicable if the pump has been damaged by accident, improper installation, unreasonable use, lack of proper maintenance, unauthorized repairs or modifications, or other causes not arising out of defects in materials and workmanship.
Attwood’s obligations under this warranty are limited to repair of the product at Attwood’s plant or replacement of the product at Attwood’s option and at Attwood’s expense. Any expenses involved in the removal, reinstallation, or transportation of the product are not covered by this warranty. The product must be returned to Attwood’s plant at the address indicated above, postage prepaid, with proof of original purchase, including date. If Attwood is unable to replace the product and repair is not commercially practicable or cannot be timely made, or if the original consumer purchaser is willing to accept a refund in lieu of repair of replacement, Attwood may refund the purchase price, less an amount for depreciation. The acceptance by Attwood of any product returned or any refund provided by Attwood shall not be deemed an admission that the product is defective or in violation of any warranty.
This warranty is Attwood’s only express warranty of this product. No implied warranty shall extend beyond one (1) year from the date of original consumer purchase. Attwood shall not be liable for any damages for loss of use of this product, nor for any other incidental or consequen- tial damages, costs or expenses.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
© 2003 Attwood Corporation |
|
1016 N. Monroe Street, Lowell, MI | www.attwoodmarine.com |