Aube Technologies TH101D manual Summary, Installation, Connecting wires and mounting thermostat

MODEL TH101D

SUMMARY

uOPTIONS SELECTION

To change the temperature from °C to °F and back, maintain DAY button pressed down as RESET button is being pressed on and released. Then release DAY button.

To change the time format from 24 hours to 12 hours and back, maintain HOUR button pressed down as RESET button is being pressed on and released. Then release HOUR button.

To change the heating control from proportional to on/off and back, maintain MIN button pressed down as RESET button is being pressed on and released. Then release MIN button.

uTO SET TIME AND DAY

Press on DAY, HOUR and MIN buttons to adjust time and day.

uTO RECORD THE HEATING PROGRAMS

Set the operating mode to AUTO. Use the PGM button to select the program to be recorded or modified. Once the program is selected, use HOUR and MIN buttons to set time and or to select temperature setting.

uTO RECORD THE ECONO PROGRAMS

Set the operating mode to ECONO. Use the PGM button to select the program to be recorded or modified. Once the program is selected,

use DAY, HOUR and MIN buttons to set time and or to select temperature setting.

uOPERATING MODES

To select an operating mode, use MODE button.

AUTO:	Runs the program.	or	shows temperature setting
	and can override temporarily your programming.
MAN:	Maintain the selected temperature.			or	change
	the temperature setting.

ECONO: Maintain a temperature setting up to the user's pre- programmed day and time. or shows temperature setting and can override temporarily your programming.

INSTALLATION

Note : The "Problems and Solutions" section at the end of this user's guide will help you to correct your problems during the installation.

This thermostat has been designed to operate with any installation which has a RESISTIVE load not exceeding 4000 W @ 240 VAC or 2000 W @ 120 VAC such as electric baseboards, radiant ceilings and floors, electric convectors, etc. It is not compatible with a low voltage controller used by a central heating system or systems using a contactor or a relay whose current is under 1.0 A.

Electricians or experienced technicians should install the thermostat. This ther- mostat is designed to be used with a self-protected heating system equipped with thermal cut off and circuit breaker.

PARTS INCLUDED

•One (1) TH101D thermostat

•Two (2) solderless connectors

•One wallplate

•Two (2) 6-32 screws ½ inch

•Two (2) 6-32 screws, 1 ½ inches

TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRICAL SHOCK. Keep air vents of thermostat clean and free from obstructions.

1) Connecting wires and mounting thermostat

Secure the wallplate to the electrical box using the 6-32, ½ screws.

Connect the rear thermostat wires to the power supply and to the electric heater wires using solderless connectors for copper wires (there is no polarity for the wires). See schematic diagram.

Electrical box 6-32, 1/2"	Electrical box 6-32, 1/2"
Thermostat 6-32, 1 1/2"		Thermostat 6-32, 1 1/2"

Left door frame Right door frame

2-wire installation :

VAC

4-wire installation :

VAC

Push the excess wire back into the electrical box to prevent interference with the thermostat. Secure the thermostat using two (2) 6-32 screws 1 ½ inches long. Once the thermostat is properly installed, return power to heating system.

Note 1 : All cables and connections must conform to the local electrical code.

Note 2 : In normal use at full capacity (4000 W), the housing temperature of the thermostat can reach 35 to 40 °C.

WARNING : Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.

720-101002-A 1/4