Aube Technologies TH106-A-347S4 p Configuration, q Power-up, r Temperature Setting, t Schedule

pConfiguration

The configuration switches are on the back of the thermostat. The factory settings are indi- cated by the gray cells in the following table.

SW1	Early Start a	Off	On
SW2	Temperature / time format b	°C / 24-hour	°F / 12-hour
SW3	Cycle length c	15 seconds	15 minutes
SW4	Not used	-	-

a.Early Start can be used in Automatic mode only. When this func- tion is enabled, the thermostat calculates the optimal time to start heating in order to obtain the desired temperature by the set time. The thermostat re-assesses the start time daily based on the pre- vious day’s performance.

b.If you change the temperature display format, the preset temperatures ( , and ) will return to their default settings.

c.15-second cycles should be selected in most cases as it provides better temperature control. 15-minute cycles must be selected if you have a fan-equipped heater or if 15-second cycles causes light flickering (especially in rural regions).

qPower-up

Upon power-up, the thermostat is in manual mode () and displays the actual (ambient) temperature.

nPress the Hour and Min buttons to set the thermostat’s clock. o Press the Day button to set the day.

rTemperature Setting

Setpoint

The thermostat normally displays the actual temperature. To view the setpoint, press the or button briefly. The setpoint will appear for the next 5 seconds.

To change the setpoint, press the or button until the desired temperature is displayed. To scroll faster, hold the button.

Using a preset temperature

The thermostat has 3 preset temperatures:

Comfort temperature

Economy temperature

Vacation temperature

Icon	Intended use	Factory setting
	Comfort (when at home)	21°C (70°F)
	Economy (when asleep or away from home)	16.5°C (62°F)
	Vacation (during prolonged absence)	10°C (50°F)

•To use the Comfort or Economy temperature, press the or button respectively. The corresponding icon will be displayed.

•To use the Vacation temperature, press both and buttons simultaneously. The icon will be displayed.

Storing a preset temperature

To store the Comfort or Economy temperature:

Set the desired temperature using the or button. Press and

hold the appropriate button ( or ) for approximately 3 sec- onds until the corresponding icon is displayed.

To store the Vacation temperature:

Set the desired temperature using the or button. Press and hold both and buttons simultaneously for approximately 3 seconds until the icon is displayed.

sOperating Modes

Automatic - The temperature is set according to the programmed schedule. To place the thermostat in this mode, press Mode until is displayed. The icons of the current period and preset temperature are also displayed.

Temporary Bypass: If you modify the setpoint (by pressing the

, , or button) when the thermostat is in automatic mode, the new setpoint will be used until the end of the current period. When the next period starts, the temperature set for that period becomes the new setpoint.

Manual - The programmed schedule is not used. The temperature must be set manually. To place the thermostat in this mode:

nPress Mode until is displayed.

oSet the temperature using the , , or button.

tSchedule

The schedule consists of 4 periods per day which represents a typi- cal weekday. You can program the thermostat to skip the periods that do not apply to your situation. For example, you can skip periods 2 and 3 for the weekend.

Period Description Associated temperature preset

Wake

Leave

Return

Sleep

The Comfort ( ) temperature is used in periods 1 and 3 and the Economy () temperature is used in periods 2 and 4. For example, when the period changes from 1 to 2, the setpoint automatically changes from Comfort setting ( ) to Economy setting ( ).

You can have a different program for each day of the week; i.e., each period can start at different time for each day of the week. The thermostat has been programmed with the following schedule.

Period Setting MO	TU	WE	TH	FR	SA	SU
6:00	6:00	6:00	6:00	6:00	6:00	6:00
AM	AM	AM	AM	AM	AM	AM
8:00	8:00	8:00	8:00	8:00	--:--	--:--
AM	AM	AM	AM	AM
6:00	6:00	6:00	6:00	6:00	--:--	--:--
PM	PM	PM	PM	PM
10:00	10:00	10:00	10:00	10:00	10:00	10:00
PM	PM	PM	PM	PM	PM	PM

To modify the schedule:

nPress Pgm to access the programming mode. Period 1 is selected.

oPress Day to select the day to program (hold for 3 seconds to select the entire week).

pPress Hour and Min to set the start time of the selected period, or press Clear if you want to skip the period (--:-- is displayed).

qPress Pgm to select another period, or press Day to select another day. Then repeat step 3.

TH106-A-347S4 400-106-011-A 22/1/07 2/3