Audio-Technica atw1702 manual Ten Tips to Obtain the Best Results, System Operating Frequencies

7

System 10 Portable Camera-MountWireless Installation and Operation

6.Repeat for each additional transmitter. Remember to switch off all transmitters already paired before adding a new one and to use a unique ID number for each transmitter.

Note: With all transmitters turned off, the receiver’s System ID Display will cycle through all currently paired ID numbers. Turn on a transmitter to activate its pairing with the receiver. The receiver recognizes only one transmitter at a time. That transmitter must be turned off before the receiver will recognize another paired transmitter. *If that transmitter is turned off out of range, the receiver will not recognize another paired transmitter until the receiver is reset by disconnecting the power supply.

Clearing Individual ID Pairings

1.Press the receiver’s System ID button to select the ID number you wish to clear. The number will begin to blink.

2.Press and hold the Pair and then ID button for about three seconds, until the display shows a blinking “o.” This indicates that your selected ID number has been cleared.

3.Release the Pair and ID buttons and, after a few seconds, the display will stop blinking and return to normal operation.

4.Repeat to clear additional ID pairings.

Clearing All ID Pairings

1.Press and hold the receiver’s Pair and then ID button for about three seconds, until the display shows a blinking “o.”

2.Release the Pair and ID buttons. Then, within three seconds, press and hold the Pair and ID buttons again, until the display shows a blinking “A.” This indicates that all your paired ID numbers have been cleared.

3.After blinking three seconds, the “A” will change to “-” to indicate that there are no paired transmitters.

Ten Tips to Obtain the Best Results

1.Use only fresh alkaline or fully charged replaceable batteries for the transmitter.

2.Position the receiver so that it has the fewest possible obstructions between it and the normal location of the transmitter. Line-of-sight is best.

3.The transmitter and the receiver should be as close together as con- veniently possible, but not less than 6' (2 m).

4.While System 10 has been designed to conveniently mount on cameras, please keep other wireless devices (including wireless systems and routers) away from System 10 receivers. For best performance, some routers and Wi-Fi-based wireless systems may need to be up to 30 feet away from System 10 receivers.

5.The receiver antennas should be kept away from any metal.

6.Use the transmitter level control to optimize performance for your sound source.

7.If the receiver output is set too low, the overall signal-to-noise ratio of the system may be reduced. Conversely, if the Attenuator of the receiver is set too high, it may over-drive the input of the camera/ mixer, causing distortion. Adjust the output level of the receiver so the highest sound pressure level going into the camera/mixer causes no input overload, and yet permits the camera/mixer level controls to operate in their “normal” range (not set too high or too low). This provides the optimum signal-to-noise for the entire system.

8.Turn the transmitter off when not in use. Remove the battery if the transmitter is not to be used for a period of time.

9.Unplug the receiver from the AC outlet when the system is not in use.

System Operating Frequencies

Automatic Frequency Selection

System 10 wireless systems operate in automatically selected frequen- cies in the 2.4 GHz range, far from TV and DTV interference. Up to eight channels may be used together without any frequency coordination problems or group selection issues. Every time a receiver/transmitter pair is powered on, it automatically selects clear frequencies. Due to the dynamic nature of System 10 automatic frequency selection, these transmitting frequencies may change during power-up or performance if interference is encountered. These frequency changes occur at both the receiver and transmitter; they are seamless and imperceptible to the ear.

System Frequencies

For future reference, please record your system information here (the serial number appear on each transmitter, and on the bottom of each receiver):

Receiver
Model ATW-R1700	Serial Number
Transmitter
Model ATW-T100	Serial Number

1 or 2