9
Disc error
If a damaged disc or a support that cannot be read or anytime a CD is not loaded in proper position, the unit’s CD tray will open and the display will show “DISC ERROR”. In this case just remove the CD and replace with a new one or put the same one in the proper position.
Disc error
Nel caso venga inserito un disco molto danneggiato o un supporto non riconoscibile o qualora il CD venga inserito non correttamente nel cassetto, l’apparecchio apre il cassetto e visualizza sul display la scritta “DISC ERROR”. In tal caso rimuovere la causa dell’errore (inserire correttamente il CD, o sostituirlo con uno riconoscibile o non danneggiato).
Specifications
Parameters |
| Measurement conditions |
| Values |
|
Number of channels | - | 2 |
| ||
Maximum output tension |
| 0DBFS |
| 5.3Vpp (1.9VRMS) |
|
Frequency response |
|
|
| ||
Noise level |
| Band limits |
|
| |
Signal/noise ratio |
|
|
| ||
Supply | - |
| 230V |
| |
Power consumption | - |
| 40VA |
| |
Specifiche Tecniche |
|
|
|
|
|
Parametro |
| Condizioni di misura |
| Valore |
|
Numero di canali: | - | 2 |
| ||
Tensione max di uscita |
| 0DBFS |
| 5.3Vpp (1.9VRMS) |
|
Risposta in frequenza |
|
|
| ||
Livello di rumore |
| Limiti di banda |
|
| |
Rapporto segnale/rumore |
|
|
| ||
Alimentazione: | - |
| 230V |
| |
Assorbimento: | - |
| 40VA |
| |
Troubleshooting |
|
|
|
|
|
Symptom |
| Cause |
| Remedy |
|
Display off |
| The unit is in stand by |
| Deactivate the standby mode by pressing |
|
No sound |
|
|
| the button STANDBY on the |
|
No response to commands |
|
|
| front panel or STBY on the remote |
|
|
| Power cord is not correctly connected |
| Check that the plug of the cable is inserted |
|
|
|
|
| to the net Correctly |
|
|
| Burnt fuse inside the Unit |
| Contact your Audio Analogue retailer in |
|
|
|
|
| order to replace the fuse |
|
Display on |
| Interconnect Cables between Primo CD |
| Check the cable status and the correct |
|
No sound |
| VT and amplifier are not connected |
| connection |
|
|
| correctly or are faulty |
|
|
|
|
| Source selected not correctly on the |
| Check that Primo CD is well selected with |
|
|
| amplifier |
| the amplifier input selector |
|
The CD plays but Display is off |
| Display is not connected correctly or faulty |
| Contact Audio Analogue retailer to verify |
|
|
|
|
| the connections and eventual replacement |
|
|
|
|
| of the board |
|
The remote does not work |
| Batteries are down or missing |
| Insert or replace the batteries (2 AAA type) |
|
|
| Front panel of the appliance is too far or |
| Get nearer the appliance or change angle |
|
|
| the angle is not right |
|
|
|
If the remedies that have been suggested do not work or the problem is not in the above list, contact your Audio Analogue retailer.
Ricerca guasti
Sintomo | Causa | Rimedio |
Display spento | L’apparecchio è in stand by | Togliere l’apparecchio dallo stato di stand |
Nessun suono |
| by premendo il tasto STANDBY sul |
Nessuna risposta ai comandi |
| pannello frontale oppure STBY sul |
|
| telecomando |