REAR PANEL:
3. BUS Line Inputs / Outputs
The AMP1200 has two common or BUS inputs that
receives audio signals from standard
line outputs are direct
4. Remote
This switch selects the
voltage going into the trigger input to activate the amplifier. “Auto” setting senses a signal on the RCA
minutes to return from ready to standby mode.
5.Trigger Input / Output
The trigger input is a handy feature when connecting the
plug jack will accept a |
|
|
|
| |
device, or from a separate power supply. When the trigger |
|
|
|
| |
input is energized, the amp turns from standby to ON mode. |
|
|
|
| |
When using the AMP1200 with a receiver without a trigger |
|
|
|
| |
output, the voltage can come from a 12V wall wart (3.5mm |
|
|
|
| |
|
|
|
| ||
outlet and the trigger input.The AMP1200 can also provide | 9. Speaker Output Terminals |
| |||
an output trigger voltage (12DC @500mA max.) to turn on | The AMP1200 uses high quality Phoenix style connectors |
| |||
and off other devices in the audio system.When the ampli | - | for the speaker connections. Use |
| ||
|
|
| |||
Note : Remember there is a delay of approximately 15 | 2 inches of each conductor are separated. Strip away |
| |||
¼ inch of insulation from each conductor. Connect the |
| ||||
minutes before the amplifier goes to standby when using |
| ||||
appropriate conductor to each screw terminal, observing |
| ||||
the “Auto” |
|
| |||
| correct polarity. Also, please observe proper speaker wir | - | |||
|
| ||||
6. Channel Gain Control |
| ing when bridging channels. |
| ||
Each channel has its own independent level adjustment. |
| 10. Individual Channel Input |
| ||
This allows the output level of each speaker to be per | - |
| |||
All twelve channels have their own dedicated input that |
| ||||
fectly matched to its area. It can also be used to limit the |
|
| |||
| allows the connection of audio sources in addition to |
| |||
maximum audio level in a certain area. |
|
| |||
| the common BUS inputs. This is useful when using the |
| |||
|
|
| |||
7. Bridging Switch |
| AMP1200 with an audio matrix switcher. |
| ||
combined to increase the total power output.This is helpful | 11. AC Voltage Switch |
| |||
The unit is set at the factory for 115V U.S.operation;simply |
| ||||
when extra power is needed in certain areas. |
|
| |||
| connect the included IEC power cord to your wall outlet. |
| |||
|
|
| |||
Note: The minimum impedance for bridged channels is 8 | For 230V operation, move the voltage selector switch to the |
| |||
ohms.Also, please observe the proper speaker wiring when | 230V position. When operating at 230V the internal fuse |
| |||
bridging channels. Input selection and volume settings for | located in the IEC socket should also be changed. In most |
| |||
bridged channels will be controlled by the left channel.“BR” | 230V applications a separate power cord will be required |
| |||
is bridged mode and “ST” is | and is not included. |
| |||
CAUTION: Only change switch positions when the |
| 12. IEC Power Connector |
| ||
amplifier is turned off. |
| The unit comes with an IEC jack that permits removal of |
| ||
8. Input Selection Switch |
| - |
| ||
| ing the power cord for different countries. The IEC |
| |||
Each channel is capable of delivering the source from |
|
| |||
| socket also houses the main fuse holder. Plug the power |
| |||
many inputs. The three main inputs are BUS 1, BUS 2 |
|
| |||
| cord supplied with the amplifier into the amplifier and a |
| |||
and LINE IN. The selection for these inputs is done via |
|
| |||
| wall outlet or appropriate surge protector. |
| |||
the Input Selection switch associated with each channel. |
|
| |||
| CAUTION: DO NOT plug the amplifier’s power cord into |
| |||
Select the desired source input. Set the Input Selection |
|
| |||
switch to BUS 1 (will play source connected to the BUS |
| a switched outlet, such as what is provided on some Sur | - | ||
1 input), BUS 2 (will play source connected to the BUS |
| round Receivers. If you wish to have the amplifier turn on |
| ||
2 input) or LINE IN (will play source connected to that |
| when the Receiver is powered up, use one of the power |
| ||
channel’s LINE IN). |
| modes, such as Trigger or Auto. |
|
CAUTION: Only change switch positions when the amplifier is turned off.
(3)