AUDIOVOX SECURITY
Model: AS-9159
INSTALLATION GUIDE FOR:
REMOTE
POWER DOOR LOCK
INTERFACE
Printed in Taiwan | Form No. |
PRE-INSTALLATION CHECKS:
1.This module is designed to interface with any Remote Security System with Ground Pulsed door lock outputs. When interfacing to AUDIOVOX SECURITY Products, verify that the
Door Lock Interface.
2.This module will require the addition of the optional
a.Vacuum operated power door locks.
b.Door locking systems requiring key locking of drivers door in order to automatically lock all other doors.
INSTRUCTIONS:
1.Remove the driver's door panel for access to existing power door lock switch wiring.
2.Mount the module in the kick panel area of the driver's side of the vehicle.
3.In most vehicles, the door lock wires can be found in the driver's kick panel after examining the switch. If not, route the wires into the driver's door using the existing wiring tube as access.
4.Examine the existing power door lock switch in the driver's door to determine which wiring method must be used. The door switch will be one of the following:
a.
b.3- Wire negative switched lock (Some Ford and Foreign vehicles).
c.4 or 5 Wire polarity reversal lock (Most Fords and Chryslers and some GM).
5.The use of a voltage test meter will be required to determine which of the three types of switches is in your vehicle.
a.
b.
c.4 or 5 Wire polarity reversal locks: One wire will be 12 volt positive at all times, one or two wires will be Grounded at all times. All the remaining wires will be positive 12 volt when the switch is in one of two positions (lock or unlock) and will reverse to Ground when the switch is moved to the other position, (in some cars, they will be 12 volt positive in the "lock" position and Ground in the "unlock" position or just the opposite in other cars).
6.Connect the Red w/White wire from the AS 9159 Door Lock Interface to a +12 VDC battery source at the fuse box.
7.Plug the
NOTE: When using with PRO 9244, PRO 9249, APS 100, APS 200, or APS 300, it will be necessary to splice directly to the Door Lock Outputs.
8.Plug both the 4 pin and the 6 pin connectors into the
9.Refer to the applicable wiring schematic in the remote power door lock wiring supplement for connection of Green, Blue, White, Yellow, Orange and Blue w/White stripe wires.
AS-9159
MODULE
|
|
| RED |
|
| |||
|
|
|
|
| ||||
|
|
|
|
|
| FROM ALARM MODULE | ||
|
|
|
|
|
| |||
|
|
|
|
|
| * NOTE: IF THE WIRE COLORS FROM THE ALARM MODULE | ||
|
|
| GREEN |
|
| ARE RED AND BLACK, YOU MUST USE | ||
|
|
|
|
|
| |||
|
|
| RED w/ WHITE | DOOR LOCK INTERFACE | ||||
|
|
|
|
| TO 12 VDC CONSTANT SOURCE | |||
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |
|
|
| ORANGE |
|
| |||
|
|
|
|
|
| |||
|
|
|
| |||||
|
|
| BLUE w/WHITE |
|
|
| ||
|
|
| GREEN |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| BLUE |
|
|
| ||
|
|
| YELLOW |
|
|
| ||
|
|
| WHITE |
|
|
| ||
|
|
| REFER TO THE REMOTE POWER DOOR | |||||
|
|
| ||||||
|
|
| LOCK WIRING SUPPLEMENT FOR | |||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| CONNECTION OF THESE WIRES. |
Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788