Safety
This product complies with IEC/EN/UL
The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) to IEC/EN/UL
Disposal and Recycling
Europe This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in the European Union member states. To prevent
potential harm to human health and the environment, the product must be disposed of in an approved and environmentally safe recycling process. For information about your nearest designated collection point, contact your local authority responsible for waste disposal. Businesses should contact the product supplier for information about how to dispose of this product correctly. This product complies with the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS).
China
This product complies with the requirements of the legislative act Administration on the Control of Pollution Caused by Electronic Information Products (ACPEIP).
Contact Information
Axis Communications AB Emdalavägen 14
223 69 Lund Sweden
Tel: +46 46 272 18 00
Fax: +46 46 13 61 30 www.axis.com
Safety Information
Read through this Installation Guide carefully before installing the product. Keep the Installation
Guide for future reference.
Hazard Levels
Read through this Installation Guide carefully before installing the Axis product. Keep the Installation Guide for further reference.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Indicates a situation which, if not avoided, could result in damage to property.
Other Message Levels
product to function correctly.
Indicates useful information which helps in getting the most out of the product.
Safety Instructions
The Axis product shall be installed by a trained professional.
•Never mount or make connections to the Axis product while power is applied to the product. Always apply power at the end of the installation.
•The Axis product shall be used in compliance with local laws and regulations.
•To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing.
•Store the Axis product in a dry and ventilated environment.
•Avoid exposing the Axis product to vibration, shocks or heavy pressure.
•Do not install the product on unstable or vibrating brackets, surfaces or walls.
•Use only applicable tools when installing the Axis product. Excessive force could cause damage to the product.
•Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.
•Use only accessories that comply with technical specification of the product. These can be provided by Axis or a third party.
•Use only spare parts provided by or recommended by Axis.
•Do not attempt to repair the product by yourself. Contact Axis support or your Axis reseller for service matters.
•The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2.
•Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.
•Each wire shall have an area that corresponds to AWG 28– 16 (CSA) or AWG
•To allow for future maintenance, to avoid excessive strain on wires and connectors, and to avoid damage to conductor insulation, leave a service loop and make sure all cables and wires are properly supported and secured. Use the supplied cable ties.
•Make sure all the wires are connected correctly. Incorrect wiring could cause damage to the product.
•To protect the circuits against electrostatic discharge (ESD), use ESD protection when handling the product while the components and contacts are exposed.
•If using Power over Ethernet, wait with connecting the network cable to the network until the all the other wires have been connected.
•If installing the door controller on a wall, make sure the
|
| • The recommended maximum RS485 cable length is 30 m | |
|
| (98.4 ft). | |
Indicates significant information which is essential for the | |||
• Before installing the product, connect the product to the | |||
|
| ||
|
| network and configure the hardware in the product’s | |
