Australia/New Zealand
This digital equipment fulfills the requirements for RF emission according to the Class B limit of AS/NZS CISPR 22. The product shall be connected using a shielded network cable (STP) that is properly grounded.
Japan - この装置は、クラスB 情報技術装置です。こ の装置 は、家庭環境で使用することを目的としてい ます が、この装置がラジオやテレビジョン受信機に 近 接して使用されると、受信障害を引き起こすこと があります。取扱説明書に従って正しい取り扱い をして下さい。本製品は、シールドネットワーク ケーブル(STP)を使用して接続してください。また 適切に接地してください。
Safety
This product complies with IEC/EN/UL
The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) to IEC/EN/UL
Disposal and Recycling
Europe
This symbol means that the product shall not be disposed of together with household or commercial waste. Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) is applicable in
the European Union member states. To prevent
potential harm to human health and the environment, the product must be disposed of in an approved and environmentally safe recycling process. For information about your nearest designated collection point, contact your local authority responsible for waste disposal. Businesses should contact the product supplier for information about how to dispose of this product correctly. This product complies with the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS).
China
This product complies with the requirements of the legislative act Administration on the Control of Pollution Caused by Electronic Information Products (ACPEIP).
Contact Information
Axis Communications AB Emdalavägen 14
223 69 Lund Sweden
Tel: +46 46 272 18 00
Fax: +46 46 13 61 30 www.axis.com
Supported Readers
This list of supported readers is subject to change without notice. Contact your Axis reseller for information about supported readers.
This product is compatible with UL Listed Wiegand access control readers.
This product is compatible with the following RS485 access control readers:
AXIS A4011-E Reader
HID iCLASS® RW100: 6101CG40000, 6101CGM0000, 6101CK40000, 6101CK40002, 6101CK40100, 6101CK403C0, 6101CKM0000, 6101CKM0002, 6101CKM0203; RW300: 6111CG40000, 6111CG400C0, 6111CGM0000, 6111CK40000, 6111CK4000Z, 6111CKM0000; RW400:
6121CG40000, 6121CGM0000, 6121CK40000, 6121CK40003,
HID Smartid®: 8031DSAP
HID pivClass®
AptiqTM: M11, MTK15, MTMSK15, MT15, MTMS15 For information about which compatible RS485 access control readers have been verified by UL, see Requirements for UL Compliance on page 3.
Requirements for UL Compliance
This section contains information and instructions required for UL compliance. To make sure the installation is UL compliant, follow the instructions below in addition to the general information and instructions provided throughout this document. In cases where pieces of information contradict each other, the requirements for UL compliance always replace general information and instructions.
Supported Readers
•Compatibility with the following RS485 readers has been verified by UL: HID iClass RK40, HID SmartID 8031 DSHM, and AptiqQ MTMSK15.
Safety Instructions
•The Axis product shall be installed and serviced by a factory trained professional.
•The Axis product shall be installed within the protected premises (secured area).
•The Axis product shall be mounted indoors. Outdoor use has not been evaluated or approved by UL.
•All interconnecting devices shall be UL Listed and Class 2 power limited.
•All wiring methods shall be performed in accordance with NFPA70, local codes and authorities having jurisdiction.
•When the Axis product has reached the end of its useful life, dispose of it according to local laws and regulations. The product should not be disposed of together with household or commercial waste. See Disposal and Recycling on page 3.
•Battery
–The 3.0 V lithium battery used by the Axis product is a UL Recognized component. (Type: BR2032, diameter: 20 mm
