4 | BACK PANEL |
8
7 6 5
INCONTROLALLOWS AMPLIFIER OPERATIONWHEN A |
| C O N T R O L I / O | |||||||
|
|
| RING+12VLOWPOWER |
|
|
|
|
| |
|
|
|
|
|
|
|
| ||
TIP+12VCTRLENABLE |
|
| SLEEVEGROUND | ||||||
|
|
|
|
|
|
|
|
| C T R L |
|
|
|
|
|
|
|
|
| I N |
|
|
|
|
|
|
|
|
| C T R L |
|
|
|
|
|
|
|
|
| O U T |
|
|
|
|
|
|
|
|
| 1 2 V D C |
|
|
|
|
|
|
|
|
| 2 0 0 m A |
|
|
|
|
|
|
|
|
|
|
F U S E
C A U T I O N : F O R C O N T I N U E D
P R O T E C T I O N A G A I N S T R I S K
O F F I R E R E P L A C E O N LY W I T H
S A M E T Y P E A N D R AT I N G .
S E R I A L #
C H A N N E L 1 I N P U T
X L R ( B A L A N C E D )
R C A I N P U T
X L R I N P U T
R C A ( U N B A L A N C E D )
F | USE | |
| F | |
E |
| U |
S |
|
|
U | S | |
| F E | |
C H A N N E L 1 O U T P U T
P O S I T I V E | N E G AT I V E |
H i g h Pe r f o r m a n c e
A u d i o / V i d e o S y s t e m s
H a n d - M a d e i n t h e U . S . A .
www.bkcomp.com
B&K
S IM P LY B E T T E R !
C H A N N E L 2 I N P U T
X L R ( B A L A N C E D )
R C A I N P U T
X L R I N P U T
R C A ( U N B A L A N C E D )
F | USE | |
| F | |
E |
| U |
S |
|
|
U | S | |
| F E | |
C H A N N E L 2 O U T P U T
P O S I T I V E | N E G AT I V E |
A C L I N E
R I S K O F E L E C T R I C S H O C K
D O N O T O P E N
1 | 2 | 3 | 4 |
1.AC Fuse Holder - Holds the AC line fuse. This fuse is a 12 amp / 250 volt slow bow fuse. Replace only with the same type and value fuse.
2.AC Input Receptacle - For attaching the supplied AC power cord to the amplifier.
3.Speaker Outputs - For connecting the speakers to the amplifier. Explained further on page 6.
4.Speaker Fuses - For protection against amplifier damage in the case of shorted speaker wires. Replace fuse with the same type and value 6 amp slow blow.
5.Balanced (XLR) Input - For connecting signal patch cables (interconnects) from the preamplifier to the amplifier. Explained further on page 5 and 6.
6.Balanced/Unbalanced Input Select - This switch is used to configure a SINGLE AMPLIFIER CHANNEL for use as either balanced (XLR) or unbalanced (RCA) line inputs. This switch controls the amplifier channel and allows signal patch cables (interconnects) to be sourced from either balanced or unbalanced, preamplifi- er/processor or line outputs. Explained further on page 5 and 6.
7.Unbalanced (RCA) Input - For connecting signal patch cables (interconnects) from the preamplifier to the amplifier. Explained further on page 5 and 6.
8.Amplifier Control Input/Output - Provides remote switching of the amplifier's standby on/off feature. Explained further on page 8.
