WALL MOUNT GENERAL INFORMATION
HEAT PUMP WALL MOUNT MODEL NOMENCLATURE
MODEL NUMBER
CAPACITY
18- 1 1/2 Ton
24- 2 Ton
36- 3 Ton
48- 4 Ton
60- 5 Ton
VOLTS & PHASE A - 230/208/60/1 B - 230/208/60/3 C - 460/60/3
| WH 24 2 — A 08 X X X X X B | CONTROL MODULES | |
|
|
| |
|
|
| (See Chart Below) |
|
|
| COIL OPTIONS |
REVISIONS |
|
| X - Standard |
| COLOR OPTIONS | 1 - Phenolic Coated Evaporator | |
| VENTILATION OPTIONS | ||
KW | X - Beige | 2 - Phenolic Coated Condenser | |
X - Barometric Fresh Air Damper | (Standard) | 3 - Phenolic Coated Evaporator | |
| (Standard) | 1 - White | and Condenser |
| B - | 2 - Mesa Tan |
|
| M - Motorized Fresh Air Damper | OUTLET OPTIONS | |
| 3 - Colonial White | ||
| V - Commercial Room Ventilator | 4 - Buckeye Gray | X - Front (Standard) |
| - |
| T - Top (on WH30 and |
| Motorized with Exhaust |
| WH36 models. |
| E - Economizer (Internal) - Fully | FILTER OPTIONS |
|
| Modulating with Exhaust | X - One Inch Throwaway (Standard) |
|
| R - Energy Recovery Ventilator - | W - One Inch Washable |
|
| with Exhaust | P - Two Inch Pleated |
|
NOTE: For 0 KW and circuit breakers (230/208 Volt) or pull disconnects (460 Volt) applications, insert 0Z in the KW field of model number.
TABLE 1
ELECTRIC HEAT TABLE
Models |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
KW | A | BTU | A | BTU | A | BTU | A | BTU | A | BTU | A | BTU | A | BTU |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 | 16.7 | 13650 | 14.4 | 10240 | 16.7 | 13650 | 14.4 | 10240 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 | 33.3 | 27300 | 28.8 | 20475 | 33.3 | 27300 | 28.8 | 20475 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
|
|
|
|
|
|
| 14.4 | 20500 | 12.5 | 15360 | 7.2 | 20475 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SHIPPING DAMAGE
Upon receipt of equipment, the carton should be checked for external signs of shipping damage. If damage is found, the receiving party must contact the last carrier immediately, preferably in writing, requesting inspection by the carrier’s agent.
GENERAL
The equipment covered in this manual is to be installed by trained, experienced service and installation technicians.
The refrigerant system is completely assembled and charged. All internal wiring is complete.
The unit is designed for use with or without duct work. Flanges are provided for attaching the supply and return ducts.
These instructions explain the recommended method to install the air cooled
These instructions and any instructions packaged with any separate equipment required to make up the entire air conditioning system should be carefully read before beginning the installation. Note particularly “Starting Procedure” and any tags and/or labels attached to the equipment.
While these instructions are intended as general recommended guide, they do not supersede any national and/or local codes in any way. Authorities having jurisdiction should be consulted before the installation is made. See Page 1 for information on codes and standards.
Manual
Page 2
