Manuals / Brands / Household Appliance / Boiler / Baxi Potterton / Household Appliance / Boiler

Baxi Potterton Performa 24 Eco HE 14.5 Injectors (Fig. 66), 14.6 Electrodes (Fig. 66), 13.8, 14.7 Insulation (Fig. 67)

1 56

Download 56 pages, 5.64 Mb

14.0 Changing Components

39

© Baxi Heating UK Ltd 2009

14.5 Injectors (Fig. 66)

1. Remove the burner as described in Section 14.4.

2. Undo the screws securing the injector manifold to

the inlet elbow and remove the manifold.

3. Unscrew and replace injectors as required and

examine the sealing gasket, replacing as necessary.

Reassemble in reverse order.

14.6 Electrodes (Fig. 66)

1. Remove the four screws securing the combustion

box door and remove the door.

2. Undo the screws securing the burner to the

injector manifold. Draw the burner out of the

combustion box, pulling the electrode grommets from

the slots in the combustion box lower panel.

3. Disconnect the lead and grommet from the

electrode being replaced. Undo the securing screw

and withdraw the electrode to the burner.

4. Reassemble in reverse order.

14.7 Insulation (Fig. 67)

1. Remove the four screws securing the combustion

box door and remove the door.

2. Slide the side insulation pieces carefully out of their

carriers.

3. To replace the rear insulation piece it is necessary

to remove the heat exchanger as described in Section

14.3 and slide out the side pieces.

4. The combustion box door insulation piece can be

replaced by carefully bending up the two retaining

tabs.

5. Replace all insulation pieces and reassemble in

reverse order.

13.8

Injector

Manifold Inlet Elbow

Gasket

Injector

Burner

Electrode

Grommets

Electrode

Leads

Side Insulation

Rear Insulation

Front Insulation

Combustion Box

Door

Side Insulation

Electrodes

Fig. 66

Fig. 67

Contents

Main 2 Natural Gas Building Regulations and the Benchmark Commissioning Checklist Contents ISO 9001 FM 00866 Installer Notification Guidelines Legislation Codes of Practice, most recent version should be used IMPORTANT - Installation, Commissioning, Service & Repair Safe Manual Handling 1.1 Description 1.2 Contents of Pack 1.0 Introduction 2.0 General Layout 2.1 Layout 3.0 Appliance Operation 3.1 Central Heating Mode (Fig. 2) 3.2 Domestic Hot Water Mode (Fig. 3) 4.0 Technical Data Pump - Available Head 5.0 Dimensions and Fixings Dimensions 6.1 Information 6.2 Central Heating Circuit 6.3 Bypass 1. The boiler is fitted with an automatic integral bypass. 6.4 System Control 12 6.5 System Filling and Pressurising 6.6 Expansion Vessel (Central Heating only) 6.7 Safety Pressure Relief Valve (Fig. 6) 6.8 Domestic Hot Water Circuit (Fig. 7) 6.9 Showers 6.10 Hard Water Areas 14 7.1 Location 7.2 Clearances (Figs. 8 & 9) 7.3 Ventilation of Compartments 7.4 Gas Supply 7.5 Electrical Supply 16 7.6 Condensate Drain Termination to an internal soil and vent pipe External termination via internal discharge branch e.g sink waste - downstream External termination to a drain or gully External termination to a purpose made soak-away Page 18 Horizontal Flues This bend is equivalent to 1 metre Total equivalent length (up to 3m) = A+B+C+2x90Bends B AC This bend is equivalent to 1 metre 8.1 Horizontal Flue Systems The total equivalent length for this example is = 6.5 metres. Y B A C 20 8.3 Flue Accessories 8.4 Flue Duct Adaptor 8.5 Air duct adaptor 22 8.6 For Roof Terminals 8.7 Flue Dimensions 8.8 Flue Trim 8.9 Terminal Guard (Fig. 14) 9.1 Plume Displacement Kit (Fig. 14b) 24 X Y 9.2 Determining Permissible Lengths 50mm 30mm 9.3 General Fitting Notes 26 9.3 General Fitting Notes (cont.) 30mm 70 10.1 Initial Preparation 10.2 Flushing 10.3 Preparing The Boiler 28 10.4 Fitting The Boiler 10.5 Fitting the Safety Pressure Relief Discharge Pipe (Fig. 33) 10.6 Condensate Drain (see section 7.6) 10.7 Fitting The Flue 30 10.7 Fitting the Flue (Cont) 10.8 Making The Electrical Connections 10.9 Preliminary Electrical Checks 11.0 Commissioning the Boiler 32 11.1 Commissioning the Boiler 11.0 Commissioning the Boiler 11.2 Checking the Burner Pressure 12.0 Completion 34 12.1 Completion 13.0 Servicing the Boiler 13 .1 Annual Servicing 13.0 Servicing the Boiler 36 13.1 Annual Servicing (Cont) 14.1 Fan (Figs. 62 & 63) 14.2 Pressure Switch (Fig. 61) 38 14.3 Heat Exchanger (Fig. 64) 14.4 Burner (Fig. 65) 14.5 Injectors (Fig. 66) 14.6 Electrodes (Fig. 66) 13.8 14.7 Insulation (Fig. 67) 40 14.8 Gas Valve (Fig. 68) 14.9 Temperature Sensor (Fig. 69) 14.10 Safety Thermostat (Fig. 69) 14.11 Pump - Head Only (Fig. 71) 14.12 Pump - Complete (Fig. 73) 14.13 Automatic Air Vent (Fig. 73) 42 14.14 Pressure Gauge (Figs. 74 & 75) 14.15 Expansion Vessel (Fig. 76) 14.16 Condensate Trap (Fig. 77) 14.17 Pressure Relief Valve (Fig. 78) 14.18 P.C.B. (Fig. 80) 14.19 Selector Switch (Fig. 80) 44 14.20 Plate Heat Exchanger (Fig. 67) 14.21 Diverter Valve Assembly (Figs. 82 & 83) 14.21 Diverter Valve Assembly (Cont) 14.22 Flow Regulator (Figs. 85 & 86) 46 14.23 Secondary Heat Exchanger (Fig. 87) 14.24 Flue Overheat Thermostat (Fig. 88) 15.0 Illustrated Wiring Diagram Control PCB br - brown bk - black b - blue r - red y - yellow g/y- green / yellow w - white gr - grey Page Page Fault Finding Solutions Sections A to F A B F D C G Fault Finding Solutions Sections G to L H K I A B E C D 18.0 Short Parts List GAS BOILER SYSTEM COMMISSIONING CHECKLIST CONTROLS ALL SYSTEMS CENTRAL HEATING MODE COMBINATION BOILERS ONLY SERVICE RECORD Service Provider SERVICE 1 SERVICE 3 SERVICE 5