Typical Furnace Wiring:
Figure 6 – 7505A (for replacement of R8184G)
►Intermittent ignition, no valve-on or motor-off delays
Figure 8 – 7505B (for replacement of R7184B)
►Interrupted ignition,
|
| 60 | 70 |
|
L1 |
|
| 80 |
|
|
| W |
| |
L2 | SAFETY AND |
| R |
|
50 |
|
| ||
| OPERATING | 60 | 70 |
|
|
|
|
| |
| LIMITS | THERMOSTAT |
| |
|
|
| ||
|
| IGNITER |
|
|
|
|
| IGNITER |
|
|
|
| L2 (IGN) |
|
|
|
| MOTOR |
|
|
|
| L2 (MTR) |
|
|
| MOTOR | L1LIMIT |
|
|
|
|
| |
|
|
| LIMIT | |
|
|
| L2 | JUMPER |
|
|
| VALVE | TR |
|
|
| L2 (VLV) | TW |
L1
L2 |
| SAFETY AND |
| ||
|
| OPERATING |
|
| LIMITS |
IGNITER
MOTOR
OIL VALVE
60 | 70 |
|
| 80 |
|
| W |
|
| R |
|
50 |
|
|
60 | 70 |
|
THERMOSTAT |
| |
| IGNITER |
|
| L2 (IGN) |
|
| MOTOR |
|
| L2 (MTR) |
|
| L1LIMIT |
|
| LIMIT | |
| L2 | JUMPER |
| VALVE | TR |
| L2 (VLV) | TW |
CAD
CELL
CAD CELL
LOCATEDoppositeONsideOPPOSITEof
ControlSIDE OF CONTROLCAD CELL (If applicable)
CAD CELL
LOCATEDoppositeONsideOPPOSITEof ControlSIDE OF CONTROL (If applicable)
Figure 7 – 7505A (for replacement of R7184A)
►Interrupted ignition, no
Figure 9 – 7505P (for replacement of R7184P)
►Interrupted ignition,
L1
L2 |
| SAFETY AND |
| ||
|
| OPERATING |
|
| LIMITS |
IGNITER
MOTOR
| 60 | 70 |
|
|
|
| 80 |
|
|
|
| W | L1 |
|
|
|
|
| |
|
| R | L2 | SAFETY AND |
50 | 60 | 70 | ||
|
|
|
| OPERATING |
THERMOSTAT |
| LIMITS | ||
|
| |||
|
| IGNITER |
| IGNITER |
|
|
|
| |
|
| L2 (IGN) |
|
|
|
| MOTOR |
|
|
|
| L2 (MTR) |
|
|
|
| L1LIMIT |
| MOTOR |
|
|
|
| |
|
| LIMIT |
| |
|
| L2 | JUMPER |
|
|
| VALVE | TR | OIL VALVE |
|
| L2 (VLV) | TW | |
|
|
|
60 | 70 |
|
| 80 |
|
| W |
|
| R |
|
50 |
|
|
60 | 70 |
|
THERMOSTAT |
| |
| IGNITER |
|
| L2 (IGN) |
|
| MOTOR |
|
| L2 (MTR) |
|
| L1 |
|
| LIMIT | |
| L2 | JUMPER |
| VALVE | TR |
| L2 (VLV) | TW |
CAD |
| |
CELL | LOCATEDoppositeON OPPOSITEside of |
|
CAD CELL | ControlSIDE OF CONTROL | CAD CELL |
(If applicable) |
CAD
CELL LOCATEDoppositeONsideOPPOSITEof ControlSIDE OF CONTROL (If applicable)
NOTE:
Connect thermostat leads (if applicable) to the TR and TW terminals on the control or jumper the TR and TW terminals on the control as directed by the appliance wiring diagram.
NOTE: If the thermostat short cycles or operates improp- erly, it may require an isolation relay for proper operation. The Beckett A/C Ready Kit (part no. 51950U) provides this function. Wiring instructions are included with the A/C Ready Kit.
120v GeniSys Control Installation and Operation Manual
7