Behringer manual Rear panel, V-AMPIRELX1200H/LX210, Control Elements, Serial Number

V-AMPIRE LX1200H/LX210

Fig. 2.3: Control elements of the V-AMPIRE (rear panel LX1200H)

2.2 Rear panel	+ LX1200H: A loudspeaker with minimum 4 W
The V-AMPIRE features a serial insert path for external	impedance and 120 Watt power handling can be
	connected to the left output (mono). Two speakers
effects. Connect the SEND/LINE OUT connector to the
	with minimum 8 W/60 Watts each can be connected
input of your effects device. The SEND/LINE OUT output is
	to both outputs. Our ULTRASTACK BG412 series
taken directly pre-digital processor (PRE DSP), which	speakers are a perfect match because they can be
means you can use this connector also to record a “dry”	operated in either mono or stereo mode.
direct signal without any effect added. Connect the	+ LX210: Without external loudspeakers the internal
RETURN/LINE IN connector to the output of your external
effects device.	speakers run at 2 x 60 Watts stereo. You may
+ When using the serial insert path, please do not	connect two 8 W/60-Watt speakers on the left and
	right outputs. In this case, the internal speakers
set the effects device to 100% effects signal (“wet”);
	automatically shut off. For example, when using
otherwise, the direct signal will be missing.
	only the right output, it runs together with the left
+ As soon as the VAMPIRE’s LINE IN (Return) is
	internal speaker while the right internal speaker
connected, the signal is automatically routed to the	shuts off. Alternatively, when using the left output,
DSP. The input signal from the front will then be	the left internal speaker shuts off and only the right
interrupted at this point.	internal speaker is active. Our ULTRASTACK BG412
The ANALOG LINE OUTPUTS provide the stereo signal	Series is perfect for this application (at 8 W min.).
without analog speaker simulation applied.	This is the MIDI OUT/THRU connector. It is configured as
Use these connectors, for example, to connect an external	MIDI OUT but can be set to act as a MIDI THRU connector
	(see	A).
amp on stage.
+ You may use both balanced and unbalanced plugs	Use the MIDI IN to connect a foot controller, for example,
	the BEHRINGER MIDI FOOT CONTROLLER FCB1010
with the LINE OUTs.
	(see chapter 8.3 for details).
Connect the stereo connector of your FS112V footswitch	SERIAL NUMBER.
(included) to the FOOTSWITCH socket. This will enable
you to recall the presets from one bank. To switch on the	FUSE HOLDER/VOLTAGE SELECTOR. Before
tuner, hold down the DOWN button on the footswitch for	connecting the unit to the mains, make sure that the voltage
more than two seconds. You can also switch the tuner off	setting matches your local voltage.
again using the same button.	A blown fuse should only be replaced by a fuse of the
The GROUND LIFT switch disconnects (switch pressed)
	same type and rating. On some units, the fuse holder can
the ground connection at the DI OUT outputs co to effectively	be switched to one of two positions, i.e. 230 V and 120 V.
eliminate hum noise resulting from ground loops. When the	When operating the unit outside Europe at 120 V, a higher
switch is pressed (LIFT), the ground connection is	fuse rating is required (see chapter 8 “INSTALLATION”).
interrupted.	The mains connection is on an IEC receptacle. An
The DI OUT output provides the balanced stereo signal of
	appropriate power cord is included.
your V-AMPIRE. Connect this output (L/R) to two balanced	Use the POWER switch to put the V-AMPIRE into operation.
microphone inputs on your mixing console. With
	The POWER switch should be in the “off” position (not
configuration modes L1 and L2 the maximum level is reduced
	pressed) if you want to connect the device to the mains.
to -10 dBu so that you can directly connect them to the mic
	+ Attention: The POWER switch does not fully
inputs of your mixing console.
The AUX IN connector socket enables you to feed in	disconnect the unit from the mains. To disconnect
	the unit from the mains, pull out the main cord plug
additional stereo signals. This way, you can for example
	or appliance coupler. When installing the product,
play a drum computer or a playback.
	ensure the plug or appliance coupler is readily
The AUX LEVEL control is used for determining the volume
	operable. Unplug the power cord completely when
of the signal received at the AUX IN input.	the unit is not used for prolonged periods of time.
Connect two loudspeakers (LEFT/MONO or RIGHT) to these
connectors.

2. CONTROL ELEMENTS 7