Page 3 of 8

EUROPOWER

PMP6000

PMP4000

PMP1680S

once only available in the studio is ready to go wherever you do. Built-in, boutique-caliber mic preamps with switchable +48 V phantom power make it possible to use either dynamic or condenser mics with the PMP Series. The PMP6000 gives you 12 mic inputs while the PMP4000 and PMP1680S each give you 8 mic inputs.

Built-in Digital Effects Processor

The FBQ Feedback Detection system automatically shows you which frequencies are causing feedback. Just touch the FBQ button and watch the red LEDs on the 7-band graphic EQ pinpoint show you which frequencies to adjust for optimized sound, without the feedback.

The Ins and Outs

Use the CD/TAPE IN RCA inputs to feed in external stereo signals from CD players or tape decks. The VOICE CANCELLER switch eliminates the vocals from

pre-recorded music for instant karaoke applications.

CD/TAPE OUT RCA outputs send line-level signals from the mixer to a recording device. The left and right main outputs can be used for a variety of purposes, including connecting more power amps. Connect monitor power amps or active monitor speakers to the MON SEND output. Powered outputs on these mixers are available in professional Speakon-compatible format for secure operation.

Continued on next page

The new generation of PMP mixers come equipped with 24-bit FX processors, giving you 100 mind-blowing digital effect presets such as delay, chorus and reverb. Apply them to any channel, as well as to the monitors and main output. In case you’re pulling double duty as sound engineer and performer, the FX processors features a footswitch jack for remote on/off. Of course, if you have treasured outboard gear you’ve grown attached to, these mixers can integrate them into the mix while leaving out the built-in FX processor.

Changing the Channels

The PMP Series gives you excellent flexibility to accommodate whatever a performance requires. You get 12 (PMP6000) or 8 (PMP4000 and PMP1680S) channels for mics, guitars and other mono instruments. Stereo channels 13-20 (PMP6000), 9-16 (PMP4000) and

7-10 (PMP1680S) are designed to work in pairs as stereo channels, or independently for more mono instruments. All mono channels have 3-band EQ, switchable Low cut filter for eliminating infrasonics, and Clip LEDs to indicate when the input signal is too hot.

A STANDBY switch (PMP6000 and PMP1680S) mutes all mic channels during breaks, preventing the microphones from picking up noise or interference. You can leave all faders untouched while you play a CD via the CD/TAPE inputs.

 

 

SPEAKER

 

 

 

PROCESSING

 

 

 

switch allows mixer

 

PHANTOM Switch

POWER AMP

to compensate

 

provides 48V to

for speakers

STANDBY

switch selects

the XLR inputs

with limited low

button mutes

for use with

operation mode of

end frequency

all mic channels

condenser mics

power amp

response

(PMP6000)

 

VU METERS

GRAPHIC EQ

display main and

monitor output

adjusts specific

signal levels

frequencies

 

 

CD/TAPE adjusts

 

volume of CD/TAPE

MULTI-FX

IN signal in main or

PROCESSOR adds

monitor mix

selected sound

MAIN 2 knob

effect to any

(PMP4000/6000)

channel whose FX

adjusts output of

knob is turned up

MAIN 2 jacks

 

SURROUND

PHONES/CTRL

ROOM knob

knob adjusts the

adjusts headphone

amount of stereo

and control room

enhancement on

output volume

the mix. Press the

 

XPQ TO MAIN

 

button to activate

 

the effect

FX TO MON and

 

 

FX TO MAIN knobs

 

adjust amount of

 

signal from internal

 

multi-FX processor

FX (SEND)

included in main or

monitor mix

fader(s) adjust

 

signal sent to

 

internal FX

 

processor and FX

 

SEND jack(s)

 

MON (SEND)

MAIN fader(s)

MONO fader

fader(s) adjust

adjust the

adjusts output

output of MON

output of

of MONO OUT

SEND jacks and

main signal

jack

OUTPUT A when

 

 

using MON 1/

 

 

MONO mode