Behringer V-TONEGM110 manual Rear panel, Behringer V-TONE Model GM110

V-TONE GM110

With the MASTER control, you determine the overall and headphone volume of your V-TONE GM110. It should be set fully to the left when you operate the POWER switch or disconnect the instrument cable from the guitar or amp.

Use the POWER switch to put the GM110 into operation.

The POWER switch should always be in the “Off” position when you are about to connect your unit to the mains.

+Attention: The POWER switch does not fully disconnect the unit from the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time.

2.2 Rear panel

BEHRINGER® V–TONE
MODEL GM110
CONCEIVED AND DESIGNED
BY BEHRINGER GERMANY.
ASSEMBLED IN CHINA UNDER
ISO9000 CERTIFIED
MANAGEMENT SYSTEM.
CAUTION
REPLACE WITH SAME FUSE
TYPE AND RATING.
ATTENTION
UTILISER UN FUSIBLE DE
RECHANGE DE MEME
TYPE ET CALIBRE.		OUTPUT
230 V	: 50/60 Hz 70 W
FUSE:	˜T 1.0 A H 250 V

Fig. 2.2: Rear panel connectors
FUSEHOLDER / VOLTAGE SELECTION. Before you		At the D.I. OUT output (balanced XLR socket), you can tap
connect the device to the network, please make sure that		the audio signal of the V-TONE GM110 in order, for example,
your local voltage matches the voltage indicated on the		to feed it into a mixing console and record it. This audio
unit. Blown fuses may only be replaced by fuses of the		signal is frequency-corrected (Speaker Simulation). The
same type and rating. Some models allow for inserting the		level of the D.I. OUT (max. +22 dBu) is designed to provide
fuse holder in two different positions in order to switch		simple connection to mixers or other audio devices.
over from 230 V to 120 V operation, and vice versa. Please		With the GND LIFT switch, you can unplug the electrical
note that, for 120 V operation outside Europe, you need to
		bonding of the D.I. OUT, if ground loop or humming problems
use a fuse of a higher rating. The network connection is
		occur.
made via a STANDARD IEC INLET SOCKET. Use the
enclosed power cord to connect the unit to the mains.		FX SEND is the output socket for the serial effects path of
SERIAL NUMBER. Please take the time to fill out the		the GM110. You can use this to loop in the external effects
		(e.g. a wah-wah pedal) or to connect an external power
warranty card within 14 days of purchasing the device,
		amplifier, should you require a greater output. The internal
otherwise you will lose your extended warranty. Or simply
		signal path will not be interrupted. The frequency-corrected
register online at www.behringer.com.
		signal at the FX SEND socket is affected by all GM110
You can use the SPEAKER socket to connect an additional		controls.
loudspeaker to your V-TONE GM110. The external		The output of the looped-in effects device is connected to
loudspeaker should have an impedance of 4 Ohms. When
		the FX RETURN socket. When you connect a cable to this
using this socket, the internal loudspeaker is muted. For
		socket, you interrupt the internal signal path.
additional information on connecting an external
	+ Please note that, when using the serial effects path,
loudspeaker, refer to chapter 4.1.
The 6.3 mm PHONES jack allows you to monitor the GM110’s		the effects device will control the level of wet
		(affected) signal to dry (direct) signal.
audio signal with a pair of commercially available
headphones. As soon as this socket is used, the
loudspeaker will be muted.

+Since speakers can have quite an impact on the sound of a guitar amp, both the headphones and D.I. OUT signals are frequency-corrected (with speaker correction). Without this frequency correction extreme treble frequencies would deteriorate the sound.

+Low-impedance headphones may begin to produce distortion at certain volume levels. In such cases, please reduce the volume by turning back the MASTER control.

6 2. CONTROL ELEMENTS