Beko specifications DE 2541 F Programme Chart and Quick Reference Guide, Programme Sequence

On / Off

On / Off Button

Operating the dishwasher

· Turn the water tap on. Open the door of the machine.
· Check that the upper and lower arms can rotate freely.
· Pour (Put in) the detergent.
·	Close the door of the machine.
·	Push in the on/off button and check that the on/off indicator light comes on.

DE 2541 F Programme Chart and Quick Reference Guide

Before starting, it is essential that you carefully read right through the Installation & Operation Instruction booklet before plugging in to the mains socket.

Salt

Salt indicator light

Rinse Aid

Rinse-aid

indicator light

On/Off indicator light

· Check the salt and rinse aid level indicator lights before you start the machine. If necessary

add salt and rinse aid.

· Select the required programme by referring to the programme chart.

·Select the desired programme by turning the selector knob.

· Press start / stop button and check that the wash indicator light comes on.

!Do not open the dishwasher door whilst the appliance is in operation. However, in case the door is opened while the machine is working, then a safety mechanism ensures the machine immediately stops. Water may be very hot, so be careful.

! Care must be taken if opening the door, as steam and water will escape.

Wash

1 Rinse Aid Salt End

2

Start / Stop

3

4

5

1	2	3	4	5
PRE-WASH	RAPID	ECONOMY QUICK & CLEAN		INTENSIVE
No Heat	35°C	50°C	60°C	70°C

On / Off

Progress

indicator lights

Wash

End

Start / Stop

Start/Stop Button

·Press the on/off button after the programme is completed. The indicator light will go off.

·Turn off the water tap, unload the baskets.

Programme Sequence

While the dishwasher operates, "Wash" indicator light will be on. When the programme selected is completed, "Wash" indicator light will go off and "End" indicator light will come on.

How to cancel the washing programme

To cancel a programme while the machine is operating:

·Press and hold start/stop button for 3 seconds. The wash indicator light will start flashing. The machine will drain the water inside the machine for 45 seconds.

·The programme is cancelled when wash indicator light goes off. Then, you can choose and start a new programme.

!Depending on the stage of the programme you have cancelled, there may be detergent residue or rinse aid inside the machine and on the load. Make sure the items in the dishwasher are not used before washing properly.

How to change the washing programme

To change the programme selection while the machine is operating:

·Press start/stop button. The wash indicator light will go off.

·Select the new programme. Press start/stop button. The wash indicator light will be on and new programme will start.

!The new programme will NOT start right from the beginning. It will start from the stage last carried out by the previous programme selection.

Beko plc, Beko	House, Caxton Way, Watford, Hertfordshire, WD18 8UF
Tel : 01923 654650	Fax : 01923 819653 e-mail: service@beko.co.uk www.beko.co.uk
	Printed in Turkey Part no: 17 2197 01 00-02

Programme	1	2	3	4	5
symbols and	PRE-WASH	RAPID	ECONOMY	QUICK & CLEAN	INTENSIVE
temperatures
	No Heat	35°C	50°C	60°C	70°C
Programme	Pre-wash to	Lightly soiled	Most	Soiled dishes	Heavily soiled
selection	rinse and	dishes	economic		dishes
	loosen residue	30 minute	programme		requiring Hot
	- awaiting full	programme	for normally		pre-wash
	load - then		soiled dishes
	select a
	Programme
Detergent
compartment	-	A	A+B	A+B	A+B
A=25 cm³ /

15cm³ B=5 cm³

Programme	Prewash		Prewash		50°C Prewash
sequence	End	35 °C wash	50 °C wash	60 °C wash	70 °C wash
		Cold rinse	Cold rinse	Cold rinse	Cold rinse
		Hot rinse	Hot rinse	Hot rinse	50 °C rinse
		End	Drying	Drying	Drying
			End	End	End
Consumption
figures
Water (Litres)	3,6	10,2	13	10,6	14,4
Energy (kWh)	-	0,75	1,01	1,15	1,30
Duration (min)	15	30	140	58	115

*Values declared on the product or in the operating instruction booklet / programme chart and quick reference card supplied with the product are obtained in tests performed under controlled laboratory conditions

and these tests are as defined in relevant standards. These figures may vary depending on how soiled the dishes are, the water hardness level and other factors. Temperature changes exceeding 15°C may also effect these figures.

**Reference programme for the Testing Institute and energy labelling. Testing program: Eco 50°C as compliant to EN 50242 international norms.

***Due to continual improvement through research & design, specifications and design may change without prior notice.