ELECTRICAL REQUIREMENTS

Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply. Rating label is on the left hand side of the fridge inner liner.

We recommend that this appliance is connected to the mains supply via a suitable switched and fused socket in a readily accessible position. Should the mains lead of the appliance become damaged or should it need replacing at any time, it must be replaced by a special purpose made mains lead which can only be obtained from a BEKO Authorised Service Agent.

WARNING! THIS APPLIANCE MUST BE EARTHED

If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted. Destroy the old plug which is cut off as a plug with bared cord could cause a shock hazard if inserted into a socket elsewhere in the house.

The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse need to be replaced an ASTABEAB approved BS 1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store.

IMPORTANT! FITTING A DIFFERENT PLUG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

As the colours of the wires in the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mains lead of this appliance may

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

not correspond with the coloured

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

markings identifying the terminals

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in your plug proceed as follows:

GREEN &

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6mm.

 

 

 

 

 

 

 

 

 

(See diagram).

 

 

 

 

YELLOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Connect the green-yellow or

GREEN

32mm.

 

 

 

 

 

 

L

 

 

 

 

 

 

 

FITTED WITH BS 1362 13A FUSE ALWAYS FIT BS 1362 REPLACEMENT CARTRIDGE FUSE

green (Earth) wire to the terminal

 

 

 

 

 

 

 

BROWN

 

 

 

 

 

 

 

in the plug marked 'E' or with

N

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RED

 

 

 

the symbol

 

 

 

or coloured

BLUE

 

 

22mm.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

green and yellow or green.

OR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. Connect the blue (Neutral) wire

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6mm.

 

 

 

 

 

 

 

 

12mm. 6mm.

FUSE

 

to the terminal in the plug

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CORD GRIP

 

 

 

 

 

 

 

 

 

 

 

 

 

marked 'N' or coloured black.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.Connect the brown (Live) wire to the terminal in the plug marked 'L' or coloured red.

With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or in the main fuse box.

If in doubt contact a qualified electrician.

3

TRANSPORTATION INSTRUCTIONS

1.The appliance should be transported only in a vertical upright position. The packing as supplied must be intact during transportation.

2.If during the course of transport the appliance has to be transported horizontally, it must only be laid on its right hand side when standing in the front of the appliance. After bringing it to upright position,it must not be operated for at least 4 hours to allow the system to settle.

3.Failure to comply with the above instructions could result in damage occuring to the appliance. The manufacturer will not be held responsible if these instructions are disregarded.

4.The appliance must be protected against rain, moisture and other atmospheric influences.

5.When positioning your appliance take care not to damage your flooring, pipes, wall coverings etc. Do not move the appliance by pulling by the door or handle.

6.Empty any water in the drain tray before moving. See section ‘Defrosting’ and ‘Care & cleaning’ for further information.

IMPORTANT : Care must be taken while cleaning / carrying the appliance to avoid touching the bottom of the condenser metal wires at the back of the appliance as you might injure your fingers and hands.

Do not attempt to sit or stand on top of your appliance as it is not designed for such use. You could injure yourself or damage the appliance.

“IMPORTANT: Make sure that mains cable is not caught under the appliance during and after carrying / moving the appliance, to avoid the mains cable becoming cut or damaged."

Do not allow children to play with the appliance or tamper with the controls. BEKO plc declines to accept any liability should the instructions not be followed.

4

Page 2 Page 4
Page 3
Image 3
Beko TDA 735 manual Electrical Requirements, IMPORTANT! Fitting a Different Plug
Page 2 Page 4

TDA 735 specifications

The Beko TDA 735 is a highly efficient and versatile tumble dryer that has garnered attention for its blend of innovative technologies and user-friendly features. Designed to cater to the needs of modern households, this dryer not only delivers effective drying results but also prioritizes energy efficiency and convenience.

One of the standout features of the Beko TDA 735 is its large drum capacity, allowing users to dry larger loads of laundry in one go. This is particularly beneficial for families or those with busy lifestyles, as it saves time and energy. The drum is designed with a special structure that reduces creasing, ensuring that clothes look fresh and ready to wear straight from the dryer.

The dryer is equipped with a sensor drying system that automatically detects the moisture level in the laundry. This technology adjusts the drying time accordingly, ensuring that clothes are dried to the optimal level. Not only does this help in preventing over-drying, thus extending the lifespan of garments, but it also contributes to energy savings.

Another impressive technology incorporated into the Beko TDA 735 is the reverse action drum. This function rotates the drum in both directions, which helps to prevent clothes from tangling and allows for a more even drying process. Users will appreciate how this reduces the need for ironing, making laundry days less of a chore.

The dryer also comes with a variety of drying programs tailored to different fabrics and drying needs. From delicate garments to thicker towels, users can choose the perfect setting for optimal care. Additionally, the quick dry option is a convenient feature for those in need of immediate results.

The Beko TDA 735's energy efficiency is one of its most appealing characteristics. It operates effectively while using minimal power, which can significantly lower household energy bills. As an added bonus, the dryer includes a time delay function, allowing users to set it to run at night or during off-peak hours, maximizing cost savings.

In summary, the Beko TDA 735 combines spacious capacity, advanced drying technologies, and user-friendly features, making it a solid choice for households looking for a reliable and energy-efficient tumble dryer. With its emphasis on convenience and performance, it exemplifies how modern appliances can enhance daily life while being mindful of energy consumption.
Top Page Image Contents